3
VENTILATION SYSTEM REQUIREMENTS
Air flow (ventilation) through the dryer is critical
in the ability of
the dryer to function properly. Heat and air are required to dry
clothes. Heat provides energy to evaporate the moisture in the
clothes. Air is used to carry the heat to the clothes load and
exhaust the evaporated moisture outside. Without adequate air
flow, the heated air can not get to the clothes and they won’t
dry. There are two major components in providing the dryer
with adequate air flow: supply air and an exhaust system. If
either of these are severely restricted, the function of the dryer
will be reduced and in some cases lead to gases building up in
the residence to a dangerous level. Also, the better the air flow,
the better the drying performance and increased longevity of
the appliance.
SUPPLY OF MAKEUP AIR
Air that is drawn through the dryer and exhausted outside must
be replaced in the dwelling. The replacement air is known as
make-up air. Make up air is required for all types of household
devices, like furnaces, water heaters, clothes dryers, ranges,
kitchen and bathroom exhaust fans, and fireplaces.
If the dwelling is not properly ventilated, such as in a tightly
constructed house, there may not be enough make up air. If this
condition exists, gases that would normally be vented outside
will be slowed and could build up in the dwelling. Gases will
include carbon monoxide produced during combustion in
appliances such as in furnaces, water heaters, ranges, dryers
and fire places.
To insure the proper amount of make up air follow: ANZI 223.1
section 8.3.1.5: - “Make up air requirements for the operation of
exhaust fans, kitchen ventilation systems, clothes dryers, and
fireplaces shall be considered in determining the adequacy of a
space to provide air requirements” or Canadian Natural Gas and
Propane Code.
–
Improper ventilation could lead to a build up
of gases and a high concentration of carbon monoxide.
– Improper ventilation could starve the dryer of
make up air and could create a fire hazard as well as increase
drying times
Do not use plastic flexible duct to exhaust the dryer.
Excessive lint can build up inside exhaust system and create a fire
hazard and restrict air flow. Restricted air flow will increase dryer
times. If your present system is made up of plastic duct or metal
foil duct,
replace it
with a rigid or flexible metal duct.
Ensure the
present duct is free of any lint prior to installing dryer duct.
If the dryer is not exhausted outdoors, some fine lint will be
expelled into the laundry area.
An accumulation of lint in any
area of the home can create a health and fire hazard.
The dryer
exhaust system MUST be exhausted to the outside of the
dwelling!
Do not allow combustible materials (for example: clothing,
draperies/curtains, paper) to come in contact with exhaust
system.
The dryer
MUST NOT
be exhausted into a chimney, a
wall, a ceiling, or any concealed space of a building which can
accumulate lint, resulting in a fire hazard.
Exceeding the length of duct pipe or number of elbows
allowed in the "MAXIMUM LENGTH" charts
can cause an
accumulation of lint in the exhaust system. Plugging the system
could create a fire hazard, as well as increase drying times.
Do not screen the exhaust ends of the vent system, nor use
any screws or rivets to assemble the exhaust system.
Lint can
become caught in the screen, on the screws or rivets, clogging
the duct work and creating a fire hazard as well as increasing
drying times. Use an approved vent hood to terminate the duct
outdoors, and seal all joints with duct tape. All male duct pipe
fittings
MUST
be installed downstream with the flow of air.
Explosion hazard. Do not install the dryer where
gasoline or other flammables are kept or stored.
If the dryer is
installed in a garage, it must be a minimum of 18 inches (45.7 cm)
above the floor. Failure to do so can result in death, explosion,
fire or burns.
In installations where the exhaust system is not described in the
following charts, the following method must be used to determine
if the exhaust system is acceptable:
1.
Connect an inclined or digital manometer between the dryer
and the point the exhaust connects to the dryer.
2.
Set the dryer timer and temperature to air fluff (cool down)
and start the dryer.
3.
Read the measurement on the manometer.
4.
The system back pressure
MUST NOT
be higher than 0.75
inches of water column. If the system back pressure is less
than 0.75 inches of water column, the system is acceptable. If
the manometer reading is higher than 0.75 inches of water
column, the system is too restrictive and the installation is
unacceptable.
EXHAUST SYSTEM REQUIREMENTS
Use only 4 inch (10.2 cm) diameter (minimum) rigid or flexible
metal
duct and approved vent hood which has a swing-out
damper(s) that open when the dryer is in operation. When the
dryer stops, the dampers automatically close to prevent drafts
and the entrance of insects and rodents. To avoid restricting the
outlet, maintain a minimum of 12 inches (30.5 cm) clearance
between the vent hood and the ground or any other obstruction.
The following are specific requirements for
proper and safe operation of your dryer. Failure to follow these
instructions can create excessive drying times and fire
hazards.
