background image

Important Safety Instructions

Recognize safety symbols, words and labels

Safety items throughout this manual are labeled with a 
WARNING or CAUTION based on the risk type as described:

Destroy the carton and plastic bags after the dryer is unpacked. Children might use them for play. Cartons covered with 

• 

rugs, bedspreads, or plastic sheets can become airtight chambers causing suffocation. Place all materials in a garbage 
container or make materials inaccessible to children.

Clothes dryer installation and service must be performed by a qualifi ed installer, service agency or the gas supplier.

• 

Install the clothes dryer according to the manufacturer’s instructions and local codes.

• 

The electrical service to the dryer must conform with local codes and ordinances and the latest edition of the National 

• 

Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian electrical code C22.1 part 1.

The gas service to the dryer must conform with local codes and ordinances and the latest edition of the National Fuel Gas 

• 

Code ANSI Z223.1, or in Canada, CAN/ACG  B149.1-2000.

The dryer is designed under ANSI Z 21.5.1  or ANSI/UL 2158 - CAN/CSA C22.2 No. 112 (latest editions) for HOME USE 

• 

only. This dryer is not recommended for commercial applications such as restaurants, beauty salons, etc.

Do not install a clothes dryer with fl exible plastic venting material. Flexible venting materials are known to collapse, be eas-

• 

ily crushed and trap lint. These conditions will obstruct clothes dryer airfl ow and increase the risk of fi re.

The instructions in this manual and all other literature included with this dryer are not meant to cover every possible 

• 

condition and situation that may occur. Good safe practice and caution MUST be applied when installing, operating and 
maintaining any appliance.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

• 

Do not touch any electrical switch; do not use any phone in your building.

• 

Clear the room, building or area of all occupants.

• 

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• 

If you cannot reach your gas supplier, call the fi re department.

• 

Save these instructions for future reference.

Pre-Installation Requirements

This symbol alerts you to situations that 
may cause serious body harm, death or 
property damage.

This symbol alerts you to situations that may 
cause bodily injury or property damage.

 For your safety the information in this manual must be followed to minimize the risk of fi re or explosion or to 

prevent property damage, personal injury or loss of life. Do not store or use gasoline or other fl ammable vapors and liquids in 
the vicinity of this or any other appliance.

2

Important Safety Instructions ................................................2
Pre-installation Requirements ................................................2
Installation Requirements .................................................. 3-7
Installed Dimensions .............................................................8

Installation Instructions ................................................... 9-11
Reversing door ....................................................................12
Accessories/Replacement parts ............................................12
Español ...............................................................................13

Tools and materials needed for installation:

Adjustable pliers

• 

Phillips, straight, & square bit screw-

• 

drivers
Adjustable wrench

• 

Pipe wrench for gas supply (gas dryer)

• 

LP-resistant thread tape (for natural 

• 

gas or LP supply, gas dryer)

Carpenter’s level

• 

External vent hood

• 

4-inch (10.2 cm), rigid metal or semi-

• 

rigid metal exhaust duct work
3-wire or 4-wire 240 volt cord kit 

• 

(electric dryer)
4 in. (10.2 cm) clamp

• 

Gas line shutoff valve (gas dryer)

• 

½ NPT union fl are adapters (x2) and 

• 

fl exible gas supply line (gas dryer)
Metal foil tape (not duct tape)

• 

Table of Contents

 

- RISK OF FIRE -

 Read all of the following instructions before installing and using this appliance:

Summary of Contents for 137153400A

























Reviews: