Friedrich WallMaster WE10C33, Service Manual

Page: 9 / 60

6 WARMER –
Touch the button to raise the room air temperature.
7
Press both the and buttons at the same time to switch
the temperature from Fahrenheit (°F) to Celsius (°C). Repeat
Step 7 to switch from °C back to °F.
To adjust fan speed
8
Touch the Fan Speed button to see the current setting. Touch
it again t o change s peed. F1 i s the lowest setting (SLEEP
SETTING / LOW), F2 is MEDIUM, and F3 is HIGH.
To activate Smart Fan (WS cool-only models)
9
There is a fourth option, SF , when selecting the fan speed. This is
the SMART FAN function. SMART FAN DOES NOT OPERATE
IN CONJUNCTION WITH THE FAN ONLY MODE.
To activate Smart Fan (WY/WE heat-cool models)
9
Press the Smart Fan button to activate the Smart Fan. The light
will indicate that this feature is in use.
Smart Fan will adjust the fan speed automatically to maintain the
desired comfort level. For example, if the outside doors in your home
are opened for an extended period of time, or more people enter a
room, Smart Fan may adjust to a higher fan speed to compensate
for the increased heat load. This keeps you from having to adjust
the fan speed on your own.
To set the hour clock
10
Touch t he Set Hour b utton to see t he c urrent s etting. T he
. ) y l n o r u o h ( e m it e t a m i x o r p p a e h t s i d e y a l p s i d s i t a h t r e b m u n
Use the and buttons to change the settings. BE SURE
TO SET A.M. AND P.M. ACCORDINGLY. (P.M. is indicated by
a red light in the upper left corner of the display).
ELECTRONIC CONTROL OPERATION
Temp/Hour
Cool
Money Saver
®
Fan Only
Clock
Start Time
Stop Time
Power
Fan
Speed Mode
PM
Timer
On/Off
Set
Hour
Figure 1:
WS Model cool-only control pane l
Temp/Hour
Power
PM
Cool
Fan Only
Heat
Clock
Start Time
Stop Time
Smart
Fan
Fan
Speed
Mode
Timer
On/Off
Money
Saver
Set
Hour
2 3 4
1
6
5
7
9
8
10 11 12
14
13
Figure 2:
WY/WE Model heat-cool control panel
Figure 1: WS Model cool-only control panel Figure 2: WY/WE Model heat-cool control panel
If the air conditioner is installed and plugged into a proper receptacle,
it is ready to go. The fi rst time the unit is started, the compressor will
delay for three minutes. See Automatic Component Protection on the
following page.
Touch the Power button once. The unit will automatically be in
Cool mode with the temperature set at 75°F (24°C) and the fan
speed at F1, the sleep setting.
When you fi rst turn the unit on, it will be in the Cool mode with constant
fan.
On WS cool-only models, touch the Mode button once to activate
the MoneySaver® (See item 14 for MoneySaver instructions on
WY/WE models).
MoneySaver® is a feature that cycles the fan with the compressor
so that the fan does not run all the time. This saves energy and
improves dehumidifi cation. MoneySaver® will also run to test
the temperature if the off cycle is too long. Or you may prefer
constant fan for more air movement. (To return to constant fan,
touch the Mode button two more times).
On WY/WS heat-cool models, touch the Mode button once to
activate the Fan Only feature. The Fan Only setting will circulate
air in the room without the compressor coming on.
In order to run the fan by itself, do the following:
Continuing from MoneySaver® mode, touch the Mode button
once to activate the Fan Only feature (WS cool-only models).
To adjust temperature
Use the Mode button to select either the Cool or MoneySaver®
function (or Heat for WY/WE heat-cool models)
COOLER – Touch the button to lower the room air
temperature.
1
2
3
4
5
To start unit
To set mode of operation
8