GB
9
INSTALLATION OF APPLIANCE
ACCESSORIES (OPTIONAL)
INSTALLATION OF APPLIANCE
Deep tray *
Used for pastry, big roasts, watery foods. It can also be
used as oil collecting container if you roast directly on grill
with cake, frozen foods and meat dishes.
Tray / Glass tray *
Used for pastry (cookie, biscuit etc.), frozen foods.
Cİrcular tray *
Used for pastry frozen foods.
Wire grill
Used for roasting or placing foods to be baked, roasted
and frozen into desired rack.
Telescopic rail *
Trays and wire racks can be removed and installed easily
thanks to telescopic rails.
In tray wire grill *
Foods to stick while cooking such as steak are placed on
in tray grill. Thus contact of food with tray and sticking are
prevented.
Pizza stone and peel *
They are used for baking pastries such as pizza, bread,
pancake and removing baked food from the oven.
Tray handle *
It is used to hold hot trays.
TECHNICAL SPECIFICATIONS
Ensure that electrical installation is suitable for operationalising the appliance. If not,
call an electrician and plumber to make necessary arrangements. Manufacturing fi rm
can’t be hold responsible for damages to arise due to operations by unauthorized
people and product warranty becomes void.
WARNING: It is customer’s responsibility to prepare the location the
product shall be placed on and also have power utility prepared.
WARNING: The rules about electrical local standards must be adhered to
during product installation.
WARNING: Check for any damage on the product before installing it.
Do not have product installed if it’s damaged. Damaged products pose
danger for your safety.
IMPORTANT WARNINGS FOR INSTALLATION
Cooling fan shall take extra steam out and prevent outer
surfaces of appliance from overheating during operation
of oven.
This is a necessary condition for better appliance
operation and better cooking.
Cooling fan shall continue operation after cooking is
fi nished. Fan shall automatically stop after cooling is
completed.
A clearance must be left behind the enclosure where
you’ll place the appliance for effi
cient and good
operation.
This clearance shouldn’t be ignored as it’s required for ventilation system of the
appliance to operate.
RIGHT PLACE FOR INSTALLATION
Product has been designed to be mounted to worktops procured from market. A safe
distance must be left between the product and kitchen walls or furniture. See the
drawing provided on the next page for proper distances. (values in mm).
•
Used surfaces, synthetic laminates and adhesives must be heat resistant.
(minimum 100 °C)
•
Kitchen cupboards must be level with product and secured.
•
If there is a drawer below the oven, a rack must be placed between oven
and drawer.
WARNING: Do not install the product next to refrigerators or coolers. The
heat emitted by the product increases the energy consumption of cooling
devices.
WARNING:
Do not use door and/or handle to carry or move the product.
60 CM BUILT-IN OVEN INSTALLATION AND MOUNTING
Place of use for product must be located before starting installation. Product mustn’t
be installed in places which are under the eff ect of strong air fl ow.
Carry the product with minimum two people. Do not drag the product so that fl oor
isn’t damaged. Remove all transportation materials inside and outside the product.
Remove all materials and documents in the product.
Specifi cations
60 cm Built-in oven (MFA1-6.....)
Lamp power
15-25 W
Thermostat
40-240 / Max °C
Lower heater
1200 W
Upper heater
1000 W
Turbo heater
1800 W
Grill heater
Small grill
1000 W
Big grill
2000 W
Supply voltage
220V-240 V 50/60 Hz
Specifi cations
60 cm Built-in oven (MFA1-8.....)
Lamp power
15-25 W
Thermostat
40-240 / Max °C
Lower heater
1200 W
Upper heater
1200 W
Turbo heater
1800 W
Grill heater
Small grill
1200 W
Big grill
2400 W
Supply voltage
220V-240 V 50/60 Hz
Technical specifi cations can be changed without prior notice to improve product
quality.
The values provided with the appliance or its accompanying documents are
laboratory readings in accordance with the respective standards.
These values may diff er depending on the use and ambient conditions.
Figures in this guide are schematic and may not be exactly match your product.
Figure 1
