manualshive.com logo in svg

FreeWave LRS-455-EU, Manual

Share
Download
FreeWave LRS-455-EU Manual Download Page 15

LRS-455-EU Data Transceiver Users Manual 

 LUM0032AA Rev A 

Version 1.0 

8 

 

Baud Rate 

Description 

Actual Baud Rate 
(selections 0-9) 

The actual baud rate for the transceiver’s data port.  
It is desirable to set the baud rate to the highest level supported by the device to 

which it is connected.  In certain circumstances, however, this may actually result 

in slower data communications. 

Data, Parity  

There are six data word length and parity configurations available to be used with 

FreeWave transceivers. The default setting is 

0 

(8, N, 1) and is the most commonly 

used serial communications protocol. Select the appropriate option to 

communicate with the end device. 

Data Bits           Parity 

Stop Bits 

  8 

None 

1 

  7 

Even 

1 

  7 

Odd 

1 

  8 

None 

2 

  8 

Even 

1 

  8 

Odd 

1 

Modbus RTU 

Support for 

Modbus RTU

 protocol is available. The default setting for 

Modbus 

RTU

 is 

0 

(Not Enabled). 

To enable Modbus capability, set 

Modbus RTU 

to 1. 

Note:

  When using the transceiver in 

Modbus RTU

 mode, the Master Packet 

Repeat must match in every radio with 

Modbus RTU

 enabled, regardless of 

whether the network is in Point-to-Point or MultiPoint mode. The 

Modbus RTU 

mode must be selected when transceivers are configured in RS485 or RS422 

mode. 

Serial Interface 

In products for which the protocol of the data port is software selectable, use this 

menu to set the protocol of the data port. In the TTL RF board product this setting 

must be "0".  

Protocol 

Additional Information 

RS232               Also used for TTL transceivers. 

RS422               Modbus RTU mode must be enabled. See above. 

RS485               Modbus RTU mode must be enabled. See above. 

DOT                  Special for the Department of Transportation.  

Note: 

   When DOT mode is enabled, the TimeDelay settings operate the same as 

in the RS485/422 mode. 

Note: 

RS4xx mode must have Modbus RTU enabled, and TurnoffDelay set to at 

least 4. 

Setup Port 

Note: DO NOT change this setting unless the correct programming cable is 
available for the new setting.   

This setting determines which port, Main or Diagnostics, is used to enter the Setup 

Main Menu.    

 Port                     Additional Information 

Main Only              The terminal is connected to the Main Data Port.                       
Diagnostics Only   The terminal is connected to the Diagnostic Port. 
Both Ports             The terminal may be connected to either port. 

Setup mode is invoked by sending a "U" (capital) to the Diagnostics port or by 

Summary of Contents for LRS-455-EU







































Reviews:

No comments

Brands by name

Popular brands

Load more brands