Freescale Semiconductor Symphony DSP56724 Reference Manual Download Page 313 | Manualshive

Page: 313 / 436

background image

Symphony DSP56724/DSP56725 Multi-Core Audio Processors Reference Manual, Rev. 0

Freescale Semiconductor

20-1

Chapter 20
Chip Configuration Module

20.1

Introduction

The Chip Configuration module contains several registers which are used to select the features of the chip
and to control some peripheral devices’ pin switching or pin mux. Chip Configuration module features
includes:

•

Controls Shared Bus Arbitration and EMC Burst Mode and EMC Burst Mode

•

Pin Mux control of ESAI and S/PDIF Rx Clock output mux on ESAI HCKR pins

•

Shared Peripherals soft reset triggering and auto de-assertion

•

EMC phase-locked loop (PLL) control and status

20.1.1

Modes of Operation

The chip configuration registers can be accessed by both DSP cores.

20.2

Memory Map and Register Definition

shows the memory map for all the chip configuration registers.

20.2.1

Memory Map

Table 20-1. Chip Configuration Module Memory Map

Offset or

Address

Register

Access

Reset Value

Section/Page

y:$FFFFE7

Reserved

R

0x00_0000

y:$FFFFE6

External Memory Burst Control

R/W

0x00_0000

y:$FFFFE5

EMC PLL Status and Control

R/W

0x00_0002

y:$FFFFE4

Pin Mux Control

R/W

0x00_0000

y:$FFFFE3

ESAI Pin Switch Control

R/W

0x00_0000

y:$FFFFE2

Once Debug and Burst Control

R/W

0x00_0000

y:$FFFFE1

Shared Peripherals Soft Reset Control

rwm

0x00_0000

y:$FFFFE0

Shared Bus Arbitration Mode Configuration

R/W

0x00_0000

20.2.2.10/20-14

«
...
311
312
313
314
315
...
»

Summary of Contents for Symphony DSP56724





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Symphony DSP56724

Brand: QSC Pages: 10

Brand: Spectrum Research Pages: 10

Brand: Scarlett Pages: 27

Brand: Scarlett Pages: 24

ULTRA PREP PS100

Brand: ninja Kitchen Pages: 9

Brand: Springlane Pages: 80

Brand: Silvercrest Pages: 118

Brand: Lemco Pages: 35

4048A SIGNAL PROCESSING

Brand: Altec Lansing Pages: 2

Brand: Wolfgang Puck Pages: 28

Brand: izzy Pages: 13

Brand: ViewSonic Pages: 1

Brand: Johnson Pages: 20

Brand: JBL Pages: 73

Brand: Vdwall Pages: 24

Brand: Panasonic Pages: 33

Brand: Panasonic Pages: 7

Brand: Fbt Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands