CONNECTION:
After mounting the LED Status Light, ground the Black wire to chassis ground, using
the terminal provided. Route the Pink wire to the alarm control unit's Pink wire and plug
together.
Plug-In
LED Status
Indicator
Pink Wire
Pink Wire
Black Wire
LED STATUS LIGHT MOUNTING AND WIRING
Alarm
Control
Unit
Page - 21
Programming The Alarm Control Module To The Transmitter:
The alarm system is capable of being operated from up to 4 separate transmitters. The
alarm "learns" the transmitter's code, and will retain the transmitter codes for approximately
24 hours if its 12 volt power is removed. Depending upon on how long the alarm has been
unpowered, one of two transmitter code learning procedures are followed:
Code Learning Method #1: If the alarm has not been supplied power for more than 24 hours
there will be no codes stored. Upon power-up, the unit will enter the transmitter code
learning mode. At any time after this point press the large transmitter button. The alarm will
confirm that the code was learned by responding with a siren burst and then a chirp. After
this confirmation, there is a 20 second period in which the second transmitter may be
learned. When the second transmitter's large button is pressed, the alarm will respond with
a siren burst and two chirps. If additional transmitters are learned, the response will be a siren
burst and three chirps, then a siren burst and four chirps, until the maximum four transmitters
are learned. Only the large transmitter button needs to be pressed. The alarm will
automatically respond to the small button when it is used. The alarm will be removed from
the transmitter code learning mode from these operations: first, 20 seconds of no transmitter
activity; second, pressing the same transmitter's large button again, which will arm the
system, or third, having the alarm learn the maximum of four transmitters.
Code Learning Method #2: If the alarm has been without power for less than 24 hours the
existing transmitter codes will be retained. Upon powering up the alarm, if a transmitter
whose code is stored in the alarm's memory is used, pressing its large button will arm the
alarm, which also removes it from the code learning mode. If, however, a transmitter is
used that is not in the alarm unit's memory, the existing codes will be removed. This is
important to remember, for if a third or fourth transmitter is being coded to an existing
Page - 22
alarm system, the alarm may be unpowered for more than 24 hours; or, by using the
following procedure:
Since entering an unknown transmitter will erase all stored codes, and entering a known
transmitter code will end the code learning mode, this procedure must be followed: When
coding an additional transmitter, the new transmitter code must be presented first, then the
original transmitters must be relearned.
Regardless of which method is employed to code transmitter to the alarm control unit,
remember that the alarm unit is also in self diagnostic mode. If the Blue negative instant
trigger wire is grounded, or becomes grounded while attempting to learn transmitter codes,
the alarm will not accept the transmitter codes. This condition will be indicated by the siren
chirping three times.
Operating A Second Vehicle's Alarm: When the second vehicle's alarm is in the
transmitter learn mode, press both of the first vehicle's transmitter buttons. On this
transmitter, the first vehicle will arm and disarm from transmitter's large button, and the
second from the large and small buttons pressed together. The small button will still work
normally.
Sometimes You Have To Transmit Close To The Vehicle:
This F.C.C. approved Radio Frequency car alarm must accept any interference it may
be subject to. If you are parked close to a radio tower or other areas where there is a high
level of interference, you may need to get closer to the vehicle. If this is not the case, you
should check the system antenna, if you experience low operating range all the time.
Reposition the antenna to a different position. If you have not securely connected the red or
black power wires you could also experience low range. Replace your transmitter battery
if its red LED light is weak.
Page - 23
L I M I T E D L I F E T I M E W A R R A N T Y
Products manufactured and sold by OMEGA RESEARCH & DEVELOPMENT, INC. (the Company),
are warranted to be free from defects in materials and workmanship under normal use. If a product sold by
the Company proves to be defective, the Company will repair or replace it free of charge within the first year
and thereafter all parts to be repaired will be free with only a nominal charge for Omega Research and
Development, Inc.'s labor and return shipping, to the original owner during the lifetime of the car in which
it was originally installed.
All products for warranty repair must be sent postage prepaid to Omega Research & Development, Inc.,
P.O. Box 508, Douglasville, Georgia 30133, with bill of sale or other dated proof of purchase. This warranty
is nontransferable and does not apply to any product damaged by accident, physical or electrical misuse or
abuse, improper installation, alteration, any use contrary to its intended function, unauthorized service, fire,
flood, lightning, or other acts of God.
This warranty limits the Company's liability to the repair or replacement of the product. The Company
shall not be responsible for removal and/or reinstallation charges, damage to or theft of the vehicle or its
contents, or any incidental or consequential damages caused by any failure or alleged failure of the product
to function properly. Under No Circumstances Should This Warranty, Or The Product Covered By It, Be
Construed As A Guarantee Or Insurance Policy Against Loss. The Company neither assumes nor authorizes
any person or organization to make any Warranties or assume any liability in connection with the sale,
installation, or use of this product.
This device complies with FCC Rules part 15. Operation is subject to the following two
conditions, (1) This device may not cause harmful interference and, (2) This device must
accept any interference that may be received, including interference that may cause
undesired operation.
The manufacturer is not responsible for any radio or TV interference caused by unautho-
rized modifications to this equipment. Such modifications could void the user's authority to
operate the equipment.
MA_FRE-411ATV.REV2
