manualshive.com logo in svg

Freedom Won LiTE Business 40/32, Installation Manual

Share
Download
Freedom Won LiTE Business 40/32 Installation Manual Download Page 18

Freedom LiTE Installation Manual Revision 14 

 

                        P a g e  

17 | 30

 

 

 

Fig 4.2 Pin Configuration for standard Type T-568B RJ45 plug 

Table 5.2 Inverter End Pin Configuration for CAN Bus Control Cable for some supported 
inverters 

–

 for further information refer to the Freedom LiTE and eTower Interfacing Guide. 

Inverter Brand 

CAN L 

CAN H 

Comments 

Axpert / Kodak:  King, Max and 
VMIII 

 

 

Requires a CAN Bus to RS485 
converter that is available from 
Freedom Won.  Enquire from 

[email protected]

 

Goodwe: ES  

Pin 5 
(blue/white) 

Pin 1 
(orange/white) 

LiTE to Type 1 RJ45 cable required 
for connecting CAN Bus from LiTE to 
Goodwe 

–

 available from Freedom 

Won.  Enquire from 

[email protected]

 

Growatt / Sunforce: 5kW 

Pin 4 (Blue) 

Pin 5 
(Blue/white) 

LiTE to Type 1 RJ45 Cable required 
for connecting CAN Bus from LiTE to 
inverter, available from freedom 
won.  Enquire from 

[email protected]

 

Imeon: 3.6 and 9.12 

Pin 2 (orange) 

Pin 1 
(orange/white) 

Type Imeon RJ45 cable required for 
connecting CAN Bus from LiTE to 
inverter 

–

 available from Freedom 

Won.  Enquire from 

[email protected]

 

Ingeteam: Ingecon Sun, Storage 
1Play, 3TL and 6TL 

Open terminal 

Open terminal 

Labelled on inverter 

Koyoe: 3kVA Hybrid 

 

 

Please connect Freedom Won if you 
need to connect on of these 
inverters to a LiTE 

MLT: PowerStar 10, Oasis, 
Nomad MPPT 

Pin 5 
(blue/white) 

Pin 4 (blue) 

The MLT range of products offers 
complete CAN Bus interfacing.  
PowerStar 10 and Oasis 

–

 use a LiTE 

to Type 1 RJ45 Ethernet cable 

–

 

available from Freedom Won.  
Nomad 

–

 a CAN terminal plug is 

provided on the PC board of the 
Nomad with a resistor that can be 
enabled with a bridge.  Please see 
Nomad manual.  

Revo: 5kVA 

Pin 5 
(blue/white) 

Pin 4 (blue) 

Requires Type 1 CAN Bus cable 

–

 

available from Freedom Won.  

Summary of Contents for LiTE Business 40/32































Reviews:

No comments

Brands by name

Popular brands

Load more brands