Free Hot Water Freedom 5002 Installation, Operation And Maintenance Manual Download Page 51

 

 

 

 

 

  Page 51 

 

 

 

Collector Array Isolation RETURN Valve 

Valve is normally open during operation. It is closed to isolate the storage 
tank should the storage tank need servicing or replacing. When closed 
the circulating pump is isolated from the solar collector loop piping.   
Never shut these valves while the circulating pump is in operation.  

Collector Array Isolation SUPPLY Valve 

Valve is normally open during operation. It is closed to isolate the storage 
tank should the storage tank need servicing or replacing.  When closed 
the circulating pump is isolated from the solar collector loop piping.   
Never shut these valves while the circulating pump is in operation.  

Cold water supply line isolation ball valve -

this valve is normally open 

and allows potable water to fill the solar storage tank.  when closed the 
solar storage tankis isolated from the pressurized city cold water supply 
line piping.

Isolation Valve  15A - page 12 

Valve is normally open during operation. It is closed to isolate the storage 
tank should the storage tank need servicing or replacing.

Isolation Valve  15C - page 12

Valve is normally open during operation. It is closed to isolate the storage 
tank should the storage tank need servicing or replacing.

Isolation Valve  - 15B - page 12

Valve is normally closed during operation. It is open to isolate the storage 
tank  and 15A and 15C is cloesed should the storage tank need servicing 
or replacing.

FREEZE Instruction:  A 50% concentration of propylene glycol and 
distilled water can protect your solar system to temperatures as low as -
27° f.   Lesser concentrations of glycol and distilled water will provide a 
lower level of freeze protection.  Please consult section your installation 
manual for specific freeze tolerance information.  

Summary of Contents for Freedom 5002




























































Reviews: