background image

 

-11- 

Transport:

 

Lift the winch with the 3-point linkage and proceed with caution. 
Avoid sharp turns, to avoid tipping the tractor and/or prevent breaking the forestry chains when the 
logs bundle-up against the skid plate. 

 
LOGS MUST ALWAYS BE ATTACHED TO THE TOW BAR WITH THE FORESTRY CHAINS WHILE 
IN TRANSPORT POSITION.  THIS WILL LOWER THE CENTER OF GRAVITY OF THE TRACTOR 
AND PREVENT THE TRACTOR FROM TIPPING OVER, IF AN OBTACLE IS HIT, AND PREVENT 
SEVERE DAMAGE TO THE WINCH! 
 
LUBRICATION AND MAINTENANCE

 

 

  Lubricate the PTO shaft once daily. 

  Lubricate the drive chain once every week with a 

small amount

 of grease only. 

NEVER USE 

OIL

, these liquid lubricants may seep down and get on the clutch lining, which is located directly 

below the drive chain. No oil should ever be used, since it might penetrate the clutch lining 
(15509) surface, and would cause the clutch to slip. 

  Clean off the dirt and grease the TOP Pulley support table, once every day, to enable the pulley 

to pivot freely. This will prolong the life of the wire cable and the pulley. Use grease only. 

  Use only original Fransgård replacements parts, do not make any modifications. The drive 

chain is a metric chain, which is hardened to avoid stretching under load, other drive chains will 
stretch and wear out the main drive gear. The outside wraps of the cable are made of special 
hardened steel (Warrington seal). This cable is designed specifically for this application since 
most cables are not designed to be dragged on the ground, stones etc. These are just a few of 
the several reasons why you should demand and only use Fransgard genuine replacement 
parts when servicing your product. 

  Lubricate the cable using a very small amount of grease on a rag and wipe the cable, when it is 

fully extended. 

AVOID USING OIL SINCE IT WILL IMPREGNATE THE CLUTCH SURFACE 

OF THE CABLE DRUM AND CAUSE

 

THE CLUTCH TO SLIP

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for V-3004

























Reviews: