manualshive.com logo in svg

Franklin Electric SubDrive1100 Connect IP 23, Owner'S Manual

Share
Download
Franklin Electric SubDrive1100 Connect IP 23 Owner'S Manual Download Page 36

36

SubDrive Connect

Advanced Setup (Wi-Fi / FE Connect Mobile App)

Some advanced features are able to be modi ed when connected to the SubDrive through 
Wi-Fi and using the FE Connect mobile app. Follow the instructions below to connect to the 
drive and access these advanced settings and features.

Connecting to Wi-Fi

1.  The drive’s Wi-Fi radio is only able to be connected to within  fteen (15) minutes 

following a power-up. If the drive has been powered on for longer than  fteen (15) 
minutes, cycle power to the SubDrive unit. 

2.  After a few seconds of initialization following power-up, the FE Connect light will 

illuminate solid to indicate that a connection is available. If the FE Connect light is 

ashing, a previously-connected device is within range of the drive and is attempting 

to connect. The FE Connect light is located just below the clear window of the 
display.

3.  Open the Wi-Fi connection settings on the device you wish to use to connect to the 

drive. This is similar to the method used to connect to a normal Wi-Fi hotspot. In the 
list of available Wi-Fi connections locate the hotspot named  FECNCT XXXXX , 
where  XXXXX  is the ending portion of the serial number of the drive being 
connected to.

4.  Connect to the Wi-Fi hotspot. The FE Connect light on the drive will  ash to indicate 

that a connection is being made. Only one (1) device can be connected to a drive at 
any given time.

 

NOTE: The Wi-Fi connection will stay active for an unlimited amount of time as long 
as the mobile device is not disconnected from the drive Wi-Fi. If the connection is 
broken, the drive Wi-Fi will be available for reconnection for one (1) hour following a 
disconnection. If you wish to reconnect to the drive Wi-Fi after an hour has elapsed, 
the drive must be power cycled.

Serious or fatal electrical shock may result from contact with internal electrical components. 
DO NOT, under any circumstances, attempt to modify DIP switch settings until power has been 
removed and 5 minutes have passed for internal voltages to discharge! Power must be removed for 
DIP switch setting to take e ect.

FE Connect Light

WARNING

V

!

Summary of Contents for SubDrive1100 Connect IP 23





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands