background image

 

 
 
         

?

 

It is recommended that a separate circuit, serving only your ice maker, be provided. 
Use receptacles that cannot be turned off by a switch or pull chain. 

?

 

Do not connect or disconnect the electric plug when your hands are wet. 

?

 

Never unplug the ice maker by pulling on the power cord. Always grip the plug firmly 
and pull straight out from the outlet. 

?

 

Never clean ice maker parts with flammable fluids. Do not store or use gasoline or 
other flammable vapors and liquids in the vicinity of this or any other appliance. The 
fumes can create a fire hazard or explosion. 

?

 

Before proceeding with cleaning and maintenance operations, make sure the power 
line of the unit is disconnected and the water line is shut off. (EXCEPTION: When 
cleaning the machine’s ice making and water systems, see pages 16 – 17.) 

?

 

Before operating, put all the enclosure panels back into their original place. 

?

 

Do not touch the evaporator with your hand when the machine is operating. 

?

 

Unplug the ice maker or disconnect power before cleaning or servicing. Failure to do 
so can result in electrical shock or death. 

?

 

Do not attempt to repair or replace any part of your ice maker unless it is specifically 
recommended in this manual. All other servicing should be done by a qualified 
technician. 

 
 

 

?

 

Use two or more people to move and install ice maker. Failure to do so can result in 
back or other injury. 

?

 

To ensure proper ventilation for your ice maker, the front of the unit must be 
completely unobstructed. Choose a well-ventilated area with temperatures above 50ºF 
(10ºC) and below 100ºF (38ºC). This unit MUST be installed in an area protected from 
the elements, such as wind, rain, water spray or drips. 

?

 

The ice maker should not be located next to ovens, grills or other sources of high heat. 

?

 

The ice maker must be installed with all electrical and water connections in accordance 
with state and local codes. A standard electrical supply (115 VAC only, 60 Hz, 20A), 
properly grounded in accordance with the National Electrical Code and local codes and 
ordinances is required. 

?

 

Do not kink or pinch the power supply cord or drain lines between the ice maker and 
the cabinet. 

?

 

The fuse (or circuit breaker) size should be

 

20 amperes. 

?

 

It is important for the ice maker to be well leveled for proper operation. You may need 
to make several adjustments to level it. 

?

 

All installations must be in accordance with local plumbing code requirements. 

?

 

Make certain that the hoses are not pinched or kinked or damaged during installation. 

?

 

Check for leaks after connection. 

?

 

Although the unit has been tested at the factory, due to long-term transit and storage, 
the first batch of cubes must be discarded. 

?

 

Remove the packing materials and clean the ice maker before using. 

Summary of Contents for FIM400

























Reviews: