background image

 

11 

3.

 

You will find a strain relief bracket in the accessory package.    Fix the power supply 
cord below the bracket, as shown in the previous illustration.   

4.

 

The other end of the power supply cord  should be connected to an outlet that is in 
accordance with the local electrical code. 

 

Water Supply 

The water supply should be ready at the point of installation. The water supply pressure 
should be a minimum of 15 psig with a static pressure not more than 80 psig. (A wall 
outlet directly behind the ice maker will make installation easier.) 

 
IMPORTANT: 

1.

 

All installations must be in accordance with local plumbing code requirements. 
Professional installation is recommended. 

2.

 

Make certain that the hoses are not pinched or kinked or damaged during installation. 

3.

 

Check for leaks after connection. 

Tools required: 

½

?

  open-end wrench, Phillips screwdriver 

Connecting the water line: 

1.

 

Turn off main water supply.   

2.

 

Find a 

½

?

 

to

 ¾

?

 

vertical water pipe near the installation location. The distance 

should be less than 9 feet. The water supply hose provided with the ice maker is about 
9 feet long. 

3.

 

A shut-off valve must be installed to the main water supply. If the water pipe has a 

plain piece of copper tubing, attach a 

¼

?

O.D. compression union to the tubing and 

remove the nut. 

4.

 

Connect nuts of the water supply hose to tap and water inlet valve. Tighten firmly by 
hand, then one-half turn with wrench. 

5.

 

Turn on main water supply and tap. Check for water supply connection leaks. Tighten 
every connection (including connections at the water inlet). 

 

Installation Types 

This ice maker has only been designed for mobile (free-standing) installation. There 
must be adequate air space around the unit for ventilation purposes. (See page 7.) 

Mobile installation: 

A mobile installation will allow you to install the ice maker free-standing in any place 
you desire provided you have access to a water supply. You must follow the stated 
instructions for 

a.

 

Electrical requirements 

b.

 

Water supply 

Cleaning before use

 

After you remove all tape from the machine, clean the inside of your ice maker and ice 
storage bin before using them. See “Interior Cleaning” in the 

Cleaning and Maintenance 

section. 
 
 

Summary of Contents for FIM400

























Reviews: