Remove all grub-screws from threaded holes on
your G-Plates.
PRO TIP:
LEAVE THE GRUB-SCREWS IN YOUR STACKING PLATES TO
FURTHER HELP IDENTIFY WHICH HOLES TO HAVE THE GUIDE PINS
FOLLOW THROUGH. REMOVE THE GRUB-SCREWS FROM EACH PLATE
BEFORE STACKING ANOTHER.
FIGURE 1-A
GRUB-SCREW (THREADED HOLES)
FIGURE 1 - (BOTTOM PLATE / “THREADED HOLES”)
FIGURE 2 - (STACKING PLATES / “TOP PLATE”)
FIGURE 2-A - (INSTALLING CASTER WHEELS)
If installing Caster Wheels, you must install to your
bottom 36G plate before stacking other plates.
Be sure to lock your wheels before stacking other
plates.
FIGURE 3
S
P
IG
O
T
PACKING FOAM
After Guide Pins are removed,
thread the supplied hardware to
the bottom plate.
FIGURE 4
1. Once your 36G-Plate (“Bottom Plate”) is unpacked, move into the desired location you will be mounting the umbrella. Once in place
immediately remove and discard ALL Grub-Screws from the G-Plate (
FIGURE 1
).
NOTE:
If you are installing Caster Wheels (
+W
), do-so before stacking your “Top Plates” (If you choose to use wheels after you’ve
created a stack, you will have to remove the top plate to install the wheels). Once your wheels are installed, be sure to lock them
in place while completing your stack.
2. Locate your pair of Guide Pins and hand tighten into a pair of parallel threaded holes into the 36G-SQ (“Bottom Plate”) you have set
into place (
FIGURE 1-A
) .
3. Begin to unpack your 36G-SQ “Top Plate”. Using a half of the white packing foam, place on the edge of the bottom plate already in
place and set down your plate (
FIGURE 2A
). This will help prevent any pinching of your fingers or injury.
4.
TWO PERSON JOB
: Lift your second 36G-SQ “Top Plates” (
FIGURE 2
), and slowly stack the plate over the Guide Pins. Repeat for your
third plate to complete the stack.
5. Once both plates are stacked, and over the Guide Pins, retrieve and remove the Spigot from the mast of your Aurora umbrella. Place
the Spigot over the Guide Pins (
FIGURE 3
) then remove the Guide Pins and you will have a clear visible path to the bottom plate’s
threaded holes.
6. With your Spigot in place on G-Plate stack lined up to the outer four bolts, use the supplied hardware that is packed with your
umbrella and bolt the Spigot onto the G-Plate stack threading down into the bottom plate (
FIGURE 4
). Once your Spigot is secure to
the G-Plate stack, begin to lift the Aurora onto the Spigot until you hear an audible “click” indicating your umbrella is secure.
Your Aurora Cantilever comes with the Spigot already inserted in the mast of your umbrella. Once you have properly stacked your G-Plate,
remove the Spigot from your umbrella and you can begin to mount your Spigot to the plate stack, and then the umbrella. (see
FIGURE 4
).
36Gx2 SQUARE GALVANIZED PLATE STACK
GRUB-SCREWS ARE IN PLACE TO PROTECT THE THREADED HOLES ON BASES
DURING SHIPPING AND STORAGE. THEY MUST BE REMOVED AND DISCARDED
BEFORE THE INSTALLATION OF ANY UMBRELLA.
AURORA
X16
X16
X16
6M
M
(
G
U
ID
E
P
IN
S
&
GR
UB
-S
C
R
E
W
S
)
GU
ID
E
P
IN
S
1
.4
” X .
5
” (
8
M
M A
LL
E
N K
E
Y
)
X
4 A
U
R
O
R
A / D
IO
U
B
LE S
TA
C
K
+W (WHEEL OPTION HARDWARE)
25
26
INCLUDED G-PLATE DOUBLE STACK SPECIFIC
MOUNTING HARDWARE
