background image

3 - Technical Information 

 

This product has been designed to operate in accordance with the product specification. The 
VX500 RC searchlight has the following features: 

 

 

All marine grade materials and fixings;

 

 

Electronic power supply unit;

 

 

Parabolic glass reflector;

 

 

Instant lamp re-strike. No cooling down time required;

 

 

Economical 1000 hour lamp life (300w) 1200 hour lamp life (150w);

 

 

350° horizontal rotation;

 

 

Vertical mo23° to -23°;

 

 

Motor speed 1

- 36

/sec (Pan). 1°-3.5

/sec (Tilt);

 

 

RS485 connectivity & auto home positioning;

 

 

Remote focus facility;

 

 

Self Regulating internal heater;

 

 

Toughened front glass;

 

 

Sealing to IP66;

 

 

The searchlight also performs to the following optical data: 
 

 

Xenon light source; 

 

Lamp Wattage - 300 Watts; 

 

Supply voltage 

 110v/240v AC 1Ph 50/60 Hz; 

 

Peak Beam Candlepower 

 15.4 million Lux; 

 

Range 

 3920 metres; 

 

Adjustable lamp focus, 1° spot to 10

 flood; 

 

Temperature range:  -50°C 

 

 

Xenon light source; 

 

Lamp Wattage - 150 Watts; 

 

Supply voltage 

 110v/240v AC 1Ph 50/60 Hz; 

 

Peak Beam Candlepower 

 7.6 million Lux; 

 

Range 

 2760 metres; 

 

Adjustable lamp focus, 1° spot to 10

 flood; 

 

Temperature range:  -50°C   

 

 

 

In order that the searchlight operates correctly it is imperative that competent personnel are 
responsible for the installation, operation and servicing of this equipment. Failure to adhere to 
this advice may cause premature failure or incorrect operation of the searchlight, which may 
damage the equipment or cause personal injury. 

 
 
 
 

 

  

Back To Top 

Summary of Contents for A7183 VX500 150w 115/230v Xenon
















































Reviews: