background image

Contents

1 Safety............................................................................................................ 5

2 The door is leaking sound or does not seal properly..............................7

3 The body covers do not fit.......................................................................23

4 Power issues..............................................................................................26

4.1 There is no electricity in the pod or the electricity goes on and off...................... 26

4.2 The power outlet does not work.......................................................................... 37

5 Fans and lights.......................................................................................... 41

5.1 There is no power to the fans and light...............................................................41

5.2 The ceiling light does not switch on.....................................................................47

5.3 The display light does not switch on....................................................................52

5.4 The control panel does not work......................................................................... 55

5.5 When you adjust the ceiling light, the display light is also adjusted..................... 58

5.6 One or both fans do not work..............................................................................60

5.7 The fans are noisy............................................................................................... 66

5.8 The air inside the pod does not feel fresh........................................................... 72

6 Door handle and lock................................................................................82

6.1 The door handle is loose..................................................................................... 82

6.2 The door handle is tight....................................................................................... 86

6.3 The lock latch is stiff or gets stuck...................................................................... 89

Summary of Contents for O

































































































Reviews: