background image

FPI P36-3 Zero Clearance Direct Vent Gas Fireplace

2

To the New Owner:

Congratulations!

You are the owner of a state-of-the-art Gas Fireplace by  FPI FIREPLACE PRODUCTS
INTERNATIONAL LTD.  The P36 has been designed to provide you with all  the warmth and charm
of a wood fireplace at the flick of a switch.  The model P36 has been approved by Warnock Hersey
for both safety and efficiency.  As it also bears our own mark, it promises to provide you with
economy, comfort and security for many trouble free years to follow.  Please take a moment now
to acquaint yourself with these instructions and the many features of your FPI Fireplace.

INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE

This FPI  product has been tested and listed by Warnock Hersey as a Vented Gas Fireplace Heater to the following standards:  CAN/CGA-2.17-
M91, and ANSI Z21.88b-2003/CSA 2.33b-2003.

This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home Installations, Sites,
and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.

This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes follow
the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the current CAN/CGA
B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada.

This FPI Mobile/Manufactured Home Listed appliance comes
factory equipped with a means to secure the unit.

This FPI  Mobile/Manufactured Home listed appliance comes
equipped with a dedicated #8 ground lug to which an 18
gauge copper wire from the steel chassis ground must be
attached.

This appliance may only be installed in an aftermarket
permanently located, manufactured (mobile) home, where
not prohibited by local codes.

This appliance is only use with the type of gas indicated
on the rating plate. This appliance is not convertible for
use with other gases, unless a certified kit is used.

Summary of Contents for P36-LP3













































































Reviews: