background image

 

 
IN-GNC08 

- 21 - 

© Future Products Group 

INSTALLATION 

 

 
Regulations 

GN SERIES REFRIGERATED WELL 

 - 

INSTALLATION 

 
 

Compliance 
with Local 
Requirements 

It is very important that your drop-in refrigerated well assembly is installed 
correctly and that the operation is correct before use. Installation must comply 
with local electrical, health & safety and hygiene requirements. 

 

 

Setting Up 

GN SERIES REFRIGERATED WELL 

 - 

INSTALLATION 

 
 

Unpacking 

Unpack and check the unit for damage and report any damage to the carrier 
and supplier. Report any deficiencies to your supplier. 

The well is supplied fully assembled, with the control panel mounted on the 
main assembly. 

Food dishes and supports may be packed separately. 

 

Transport 

After removal from the crate, the well assembly can be transported by fork-lift, 
with the forks either under the base unit or under the top flange. 

 

Site 
Preparation 

Ensure the well location and any joinery cut outs are made to the precise 
measurements shown in the Mechanical Drawings. Position the well in its 
allocated working position. Use a spirit level to ensure the well is level from side 
to side and front to back. (If this is not carried out, water will collect in the well). 

 

Well Assembly 
Preparation 

Remove all tapes, ties and packers, used to prevent movement during transit. 

Lift out the food dishes, grills and divider bars. 

Check that all plastic film protection has been removed from surfaces. 

 

Grounding 

WARNING: THIS APPLIANCE MUST BE GROUNDED TO EARTH 

The grounding lead, in the mains cable, must always be connected to earth. 

A binding post is also provided, to allow the cabinet to be bonded to a surge 
grounding conductor or to adjacent equipment, should this be required. 

Continued on next page 

 

 

Summary of Contents for INLINE GN Series

















































Reviews: