background image

 

 
IN-5H06/08/12-OF 

- 17 - 

© Future Products Group 

 
Lighting 

HEATED CABINETS 

 - 

SERVICING 

 
 

Test Lighting 
Components 

Before replacing an LED strip, check that the power supply and drivers are 
working. 

If there is no dc voltage at the output, the power supply or driver board should 
be replaced. 

If there is a dc output, the LED strip must be replaced.  

 

Remove Shelf 

Unplug the lighting and heating cables, and lift out the shelf module.   

See

 Cleaning.

 

 

Access to LED 
Strips 

Remove two screws to 
release the LED assembly. 

The LED strips are protected 
with plastic covers. Remove 
the plastic cover to access 
the LED strip.  

The top light assembly is 
similar to the shelf lights, but 
the correct replacement unit 
must be used.  

 

LED Strip 
Replacement 

Individual LED modules 
cannot be replaced.  A 
complete light assembly must 
be used. 

Connection is made with a 
latching plug and socket. 

Release the latch by pushing 
a small flat blade screwdriver 
into the upper orifice. 

Fit a replacement module, 
pushing the connector until it 
clicks in place. 

 

 
 
 
 

Summary of Contents for INLINE 5000C Series

































Reviews: