Four-Faith F3X36 User Manual Download Page 15

Page: 15 / 85

F3X36 Series Router

User Manual

Xiamen Four-Faith Communication Technology Co.,Ltd.

Page 15 of 85

Add

：

J1-J3, 3

Floor, No.44, Guanri Road, Software Park, Xiamen .361008.China

http://www.four-faith.com

Tel

：

+86-592-6300320 Fax

：

+86-592-5912735

Installation of antenna:

Screw the SMA male pin of the cellular antenna to the female SMA interface of the

Router with sign “ANT-M” and “ANT-A”.

Screw the SMA female pin of the WIFI antenna to the male SMA interface of the

Router with sign “WIFI”.

Warning: The cellular antenna and the WIFI antenna can not be connected wrongly.

And the antennas must be screwed tightly, or the signal quality of antenna will be
influenced!

Installation of cable:

Insert one end of the network cable into the Local network interface , and insert the

other end into the Ethernet interface of user’s device. The signal connection of network
direct cable is as follows:

RJ45-1

RJ45-2

Summary of Contents for F3X36






















































































Search results

Summary of Contents for F3X36

Reviews:

Related manuals for F3X36

Brands by name

Popular brands

Four-Faith F3X36, User Manual

Search results

Summary of Contents for F3X36

Reviews:

Related manuals for F3X36

Brands by name

Popular brands