manualshive.com logo in svg

fos4X Blackbird OECD MDE1195, Instructions For Use Manual

Share
Download
fos4X Blackbird OECD MDE1195 Instructions For Use Manual Download Page 66

9. Maintenance

6.

Connect the MC 1,5/ 2-GF-3,81 connector to the PWR
connector.

7.

Switch on the power supply.

9.2.3 Firmware Update

9.2.3.1

Firmware Update via Web Interface

TIP

The web interface is available with firmware Version 2.65 or
higher.

Condition:

■

Firmware archive for the Blackbird OECD available.

Doing a firmware update via the web interface:

1.

Open the web-interface. See 

Opening the Web Interface., page 52

.

2.

Open the page SETTINGS.

3.

Open the page FIRMWARE UPDATE.

4.

Click on SELECT FILE.

5.

Select the firmware archive.

6.

Click on OPEN.

The firmware archive is displayed in the 

Firmware image:

 field.

7.

Click on UPLOAD FIRMWARE.

The status is displayed at 

Status:

.

8.

Wait until the firmware update is complete.

9.

Reboot the Blackbird OECD. Turn the power supply off and on.

P

Firmware update complete.

66 / 76

MDE1195_4-10_1.3.x_5.0_Blackbird

OECD_(9CH, PRN)-en-us

© fos4X 2020

Summary of Contents for Blackbird OECD MDE1195













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands