Forza FDC-1502R Manual Download Page 7

Interface

Setting

 

For 200/208/220/230/240 VAC, you may choose any of the
following output voltages

200:

 the output voltage is 200VAC

208:

 the output voltage is 208VAC

220:

 the output voltage is 220VAC

230:

 the output voltage is 230VAC (Default)

240:

 the output voltage is 240VAC

For 100/110/150/120/127 VAC you may choose any of the
following output voltages

100:

 the output voltage is 100VAC

110:

 the output voltage is 110VAC

115:

 the output voltage is 115VAC

120:

 the output voltage is 120VAC (Default)

127:

 the output voltage is 127VAC

3-4. Abbreviations on the LCD display

3-5. UPS parameter settings

01: Output voltage settings

Enable

Disable

Escape

High loss

Low loss

ON

OK

Site fault

EPO

Over temperature

Charger failure

Frecuency is unstable in bypass mode

EEPROM error

Fan failure

Battery replacement

Abreviation

Display content

Meaning

HS

LS

ON

OK

sf

EE

FU

ch

ep

fA

 

Parameter 2

 

Parameter 1

 

Two parameters need to be configured in order to set up 

the UPS. Refer to following diagram. 

Parameter 1:

 it is used for the different configuration 

options. Please refer to the table below. 

Parameter 2:

 it represents the setting information or 

values of each program.

02: Frequency Converter enable/disable

Interface

Setting

Activates or cancels the converter mode. 

CF ENA:

 Enable converter mode  

CF DIS: 

Disable converter mode (Default)

 

03: Output frequency settings

Interface

Setting

Use this menu to define the initial frequency on battery mode:

BAT 50:

 The output frequency is set to 50Hz

BAT 60:

 The output frequency is set to 60Hz

If the converter mode is enabled, the following options
will be available:

CF 50: 

The output frequency is set to 50Hz

CF 60:

 The output frequency is set to 60Hz

04: ECO enable/disable

Interface

Setting

Activates or cancels the ECO mode. 

ENA:

 the ECO mode is enabled

DIS:

 the ECO mode is disabled (Default)

05: AECO enable/disable

Interface

Setting

Activates or cancels the advanced ECO mode. 

ENA:

 the advanced ECO mode is enabled

DIS:

 the advanced ECO mode is disabled (Default)

Summary of Contents for FDC-1502R













Reviews: