background image

2

1-5. Maintenance, service and faults

• The voltage used by this UPS may be hazardous. The unit contains no user serviceable parts; do not attempt to 

disassemble the unit. Only qualified service technicians can perform maintenance on the unit. Failure to adhere to this 
could cause personal injury or equipment malfunction and void the warranty.

• 

Caution

 - risk of electric shock. Even after the unit is disconnected from the mains, components inside the UPS 

system are still connected to the battery packs which are potentially dangerous.

• Before carrying out any kind of service and/or maintenance, disconnect the batteries and verify that no current 

is present and no hazardous voltage exists in the terminals of high-capacity capacitors, such as BUS-capacitors. 
Servicing of batteries should be performed or supervised by experts who possess the knowledge to closely follow all 
required precautions.

• 

Caution:

 potentially hazardous voltages from the battery can still be present even after disconnecting the UPS from 

the AC mains. Therefore, the positive and negative terminals of the battery shall de disconnected prior to performing 
any maintenance or repair inside the unit.

•  A battery can present the risk of short-circuit current and electrical shock. The following precautions should be taken:
-  remove wristwatches, rings and other metal objects
-  use only tools with insulated grips and handles.
•  When replacing the battery, make sure to use the same type and number of sealed lead-acid batteries specified.
•  Do not dispose of batteries in a fire. Batteries may explode if exposed to high temperatures.
•  Never try to open a battery. The cell contains a toxic electrolyte which is harmful to the skin and eyes.
•  Replace the fuse only with the same type and amperage in order to avoid fire hazards.
•  Do not dismantle the UPS system.

2. OPERATION

2-1. Unpacking and inspection

Remove the UPS from its package and make sure that all the following items are included:
•  One UPS unit 
•  One user manual
•  One monitoring software CD (ForzaTracker)
•  One USB cable
•  Warranty certificate

Carefully inspect the UPS to check for any damages that 
may have occurred during shipping.
Should any evidence of damage be found or if some parts 
are missing, do not turn the UPS on; you must immediately 
notify the carrier or dealer where you purchased the

2-2. Product overview

Front panel view

1. Touch screen 
2. Power button 

1

2

Summary of Contents for FDC-1002T

































Reviews: