background image

 

14 

CARJACK PROTECTION 

 

ACTIVE CARJACK 

This feature provides Active Carjack protection and must be enabled before use through Alarm programming 
(option 10). See page 8.  When the Ignition is on (running), press button #2 ( Unlock Symbol ).  Parking lights 
will flash TWICE to confirm the Carjack countdown sequence.  90 Seconds later, the unit will begin a Carjack 
Cycle  consisting  of  20  seconds  of  pre-warning  chirps  turning  into  a  full  system  activation  with  siren/flashing 
light pulses for 5 min.  To reset Active Carjack, IGNITION MUST BE ON, then press Button #2 again. 
 

PASSIVE CARJACK 

This feature provides Passive Carjack protection and must be enabled before use through Alarm programming 
(options 9 and 10).  See page 8.  We recommend this mode should only be used in serious situations.  When 
the Ignition is on (vehicle is running), and a door is opened, the Carjack countdown sequence will be initiated.  
90  Seconds  later,  the  unit  will  begin  a  Carjack  Cycle  consisting  of  20  seconds  of  pre-warning  chirps  turning 
into  a  full  system  activation  with  siren/flashing  light  pulses  for  5  min.    To  reset  Passive  Carjack,  IGNITION 
MUST BE ON AND DOORS MUST BE CLOSED, then press the override/program button (3) times. 
 

FULL-TIME CARJACK 

Use  in  case  of  extreme  Carjack  threat  only.    This  feature  provides  full-time  Carjack  protection  and  must  be 
enabled before use through Alarm programming options (9) & (10).  See page 8.  EVERY TIME the Ignition is 
turned  ON  or  a  door  is  opened,  then  closed  with  the  Ignition  ON,  a  Carjack  countdown  sequence  will  be 
initiated.  90 Seconds later, the unit will begin a Carjack Cycle consisting of 20 seconds of pre-warning chirps 
turning  into  a  full  system  activation  with  siren/flashing  light  pulses  for  5  min.    You  must  reset  the  unit  every 
time the IGNITION is turned on or a door is opened and closed when the ignition is on. 

 
To RESET : IGNITION MUST BE ON AND DOORS MUST BE CLOSED

, then press override/program button 

(3) times. 
 

 

NOTE:  When FULL TIME CARJACK is in effect, it must be reset every time the key is turned on, Door 
is opened, before entering VALET mode, and before Programming options or transmitters.  It is always 
in effect each time the Ignition is turned on and/or a door is opened with Ignition on. 

 
 

 

Summary of Contents for CRIMESTOPPER FS-10

















Reviews: