Fortin E400 RF641W, Quick Installation Manual

Page: 3 / 8

FUNCTION
FUNCTION
MODE 1
DEFAULT
MODE 2
MODE 3
MODE 4
MODE 5
MODE 6
18 Diesel Mode Disable
Enable (20 seconds)
Delay between Ignition
power up and Starter
(crank).
Enable (10 seconds)
Delay between Ignition
power up and Starter
(crank).
Enable
No delay between
Ignition power up and
Starter (crank).
— —
19 Turbo timer Disable Run 2 minutes. Run 4 minutes. — — —
20
Engine supervision:
-Tachless - -analog
tach- -Tach Data-
Link-
Tachless on crank and
supervision Tach Data-
Link or analogic after
Tachless only.
( vehicles with
automatic transmission
only)
Analog Tach learning
(see p.4 for programming)
Start (crank) 8 sec
on tachless. (
vehicles with automatic
transmission only)
Start (crank) 8 sec+
Supervision by
Data-Link Tach (Data
interface required)
Tach Data-Link
only (Data interface
required)
21 Start Attempts 2 1 3 — — —
22 — — — — — — —
23 Master RESET
RESET all programming
options by default.
(Retains already
programmed remote.)
— — — — —
24
Special
application
Disable Application 1 Application 2 Application 3 — —
25
Auxiliary 1 Output
Function --> LOCK
0.5 seconds &
disarm alarm
0.5 seconds
10 sec latch or
until a button is pressed.
20 sec latch or
until a button is pressed.
30 sec latch or
until a button is
pressed.
Latch until shutdown
26 Hybrid mode Gas / Diesel vehicle Hybrid vehicle — — — —
27
Auxiliary 2 Output-
Function--> UNLOCK
0.5 seconds &
disarm alarm
0.5 seconds
10 sec latch or until a
button is pressed.
20 sec latch or until a
button is pressed.
30 sec latch or until a
button is pressed.
—
28
Manual transmission
Neutral safety switch
Special Application
No application Enable (see p.4)
For manual transmission vehicles equipped with neutral safety switch. DO NOT CUT THE LOOP.
Connect the auxiliary IN (Purple/White) to the neutral safety switch of the vehicle.
29 Alarm Duration 30 seconds 60 seconds 120 seconds — — —
30 Valet code
Ignition ON
Valet button x3 times.
Ignition ON
Valet button x3 times
and x1 times 3
seconds.
Ignition ON
Valet button x4 times
and x1 times 3 seconds.
Ignition ON
Valet button x5 times
and x1 times 3 seconds.
Ignition ON
Valet button x6
times and x1 times 3
seconds.
Ignition ON
Valet button x7 times
and x1 times 3 sec.
31
Special application
Programmable
output (+)
No special application
Priority on function 2
Special application - Function 2 (all option)
not available.
— —
Enable at ground out,
disable with vehicle
ignition off
White wire (5th relays):
Trunk )
White wire (5th relays):
(+)Parking light output
32
Configuration
Dk.Blue (Pin17)
Yellow/Red (Pin19)
wire
Dk.Blue (Ground out,
Pin17): Shut-down 1
second after remote
start run time.
------------------
Yellow/Red (Pin19)=Arm
Dk.Blue (Ground out,
Pin17): Shut-down 3
seconds after remote
start run time.
Yellow/Red (Pin19) (Arm):
Shutdown after
— — —
33 Manual transmission
function
Activated by the remote
starter remote.
See page 4.
Automatically activated
by hand-brake and Foot
Brake.
Manual sequence
completed by locking the
doors
Cancel ready mode
when trunk open.
— —
34 Trunk output Pulse 0.5 seconds Pulse 2.5 seconds
Unlock before trunk pulse
0.5sec
Trunk Output at ignition
only
— —
35 Door unlock Special
application
No special application Activate vehicle ignition
at unlock.
Activate vehicle ignition
and accessory at unlock.
— — —
36
Activation/
desactivation remote
Valet Mode
—
by remote :
FUNCTION
-->
LOCK
+
UNLOCK
or Valet button
By Valet button only — — —
37
Security Remote car
starter
Special application
No special application
Security ON: Shutdown
Engine if the door
is opened before
UNLOCK is pressed.
(Door trigger required).
— — — —
38
System control by
OEM Remote
Disable
Enable (Press 3x Lock
to remote start) (Bypass
module required)
—
Enable
Alarm controled by OEM
Remote.
Enable (Press Lock,
Unlock Lock to remote
start) (Bypass module
required)
—
39 AUX1 CONTROLED
BY Temperature
Disable
Enable : AUX1 activated
at +5
o
c when remote
started (see function
25)
— — — —
LEGEND: FUNCTION BY DEFAULT
RESETS ALL FUNCTIONS BACK TO DEFAULT AND ERASES ANY REMOTES THAT HAVE BEEN PROGRAMMED.
Disarm the
system (The
antenna led
must not be
flashing, see
enter/exit
valet mode
p.4).
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6
Turn the
Ignition
ON.
OR
Press and hold
the
valet switch or the
antenna button until
the Parking lights
turn ON, the horn/
siren will chirp.
OR
Press and
release the
valet switch
or the antenna
button
23 times.
X1
Press and
release
the brake-
pedal
once.
OR
Press and hold
the valet switch
or the antenna
button for 5 sec-
onds. The Parking
lights will flash to
confirm.
Turn the Igni-
tion OFF to
exit program-
ming. The
Parking lights
will flash 4
times.
FMH
2-W
FMH
2-W
FMH
2-W