Forney 125 FC Operating Manual Download Page 4

4

WWW.FORNEYIND.COM

Forney 6 Month Warranty

Effective July 1, 2015

1)  Limited Warranty:

 Subject to the terms and conditions below, Forney Industries, Inc., Fort Collins, 

Colorado, warrants to its original retail purchaser that the new Forney equipment sold after the effective date 

of this limited warranty is free of defects in material and workmanship at the time it is shipped by Forney. This 

is in lieu of all other warranties, express or implied.

2)  Notification:

 Please call 

1-800-521-6038

 with your warranty questions. You can also visit www.

forneyind.com for additional information about your new welder.

3)  Length of Warranty:

 Within the 6 month warranty period Forney will repair or replace any warranted 

parts or components that fail due to defects in material or workmanship. Warranty is effective from the date 

of original retail purchase. 

4)  Non-Applicable Parts: 

Forney Industries limited warranty shall not apply to consumables such as contact 

tips, cutting nozzles, felt wire cleaner, drive rollers, gas diffusers, plasma torch tips and electrodes, weld 

cables, tips and parts that fail due to normal wear. In addition, this warranty does not extend to any damage 

caused by the untimely replacement or maintenance of any of the previously listed consumable parts.

5)  Warrantor:

  

Forney Industries 

2057 Vermont Drive 

Fort Collins, CO 80525 

1-800-521-6038 

www.forneyind.com

6)  Purchaser / Warranty: 

The original purchaser of the Forney Industries product. The warranty is 

not transferable. Forney Industries products are intended for purchase and use by persons trained and 

experienced in the use and maintenance of welding equipment.

7)  What is not covered under the warranty:

A)  Implied warranties, including those of merchantability and fitness for a particular purpose are limited in 

duration to this express warranty. After this period, all risks of loss, from whatever reason, shall be on the 

purchaser.

B)  Any incidental, indirect, or consequential loss, damage, or expense that may result from any defect, 

failure or malfunction of the Forney product.

C)  Any failure that results from accident, purchaser’s abuse, neglect or failure to operate products in 

accordance with instructions provided in the owner’s manual(s) supplied with the product.

D)  Pre-delivery service, i.e. assembly and adjustment.

8)  Claim: 

In the event of a warranty claim under this warranty, the exclusive remedies shall be, at Forney 

Industries sole option:

A)  Repair; or

B)  Replacement; or

C)  Where authorized in writing by Forney Industries, the cost of repair or replacement at an authorized 

Forney Industries Service Center; or

D)  Payment of or credit for the purchase price less reasonable depreciation based on actual use upon the 

return of the goods at the customer’s risk and expense.

9)  Purchaser will:

A)  Contact Forney Customer Service at 

1-800-521-6038

 within 30 days of the defect or failure.

B)  Provide dated proof of purchase (typically a purchase receipt).

C)  Provide the serial number. Registering your welder at 

www.forneyind.com/customer_service/

register_your_product/

 will speed up this process.

D)  Deliver or ship welder to a Forney authorized Service Center. Freight &/or packaging costs, if any, must 

be borne by the purchaser.

Summary of Contents for 125 FC





























Reviews: