background image

8

CROSS FOLDING

Cross folding refers to folding a document in one pass and then running it through the folder a second time to 

be folded again.

Common Application:  Folding an 11” x 17”  document in half and then letter folding it to fi t in a standard #10 

envelope.

1.   Load folded paper into the feed tray with the fold     

crease facing the non-operator side of the folder (Fig 

13).  

Note: For best results fi rmly run your hand over the fold 

crease to help fl atten the paper before loading. 

2.   Attach the cross fold paper guide onto the feed tray  

paper guide (Fig. 14) and lower guide.

Note: Cross folding ability will vary based on the paper 

weight and type.  If the paper is too heavy it may not be 

able to be cross folded. 

Tab “B”

Tab “A”

Slot “B”

Slot “A”

Fig. 14

To install cross fold guide hook tab “A” into slot  “A” 

and then lower tab “B” into slot “B”

Fig. 13

Fold Crease

Cross Fold Guide

STACKER WHEEL POSITIONING GUIDE

Move the stacker wheels to the proper position indicated on the chart based on the fold and paper size. For 

paper between 28# and 65#* refer to the “Stacker Wheel Setup For Thick Paper” on page 9.

8.5" x 11" 8.5" x 14" 11" x 17"

Letter

Zig-Zag

Single

Gate

Fold Out

Double ll

A

A

B

A

B

A

A or B

A or B

B

B

C

A

B

B

C

C

C

A or B

Stacker Wheels

Summary of Contents for FD 380

















Reviews: