background image

4

SETTING CUSTOM FOLDS

Eccentric “Z”

1. Measure the length of panel “A”.

2. Adjust the upper fold plate so that the bar lines up with the measurements of 

panel “A”, for example: if panel “A” is  5 1/4” long move the bar up or down so 

that it lines up with the 5 1/4” mark on the fold plate.

3. Measure the length of panel “B”.

4. Adjust the lower fold plate so that the bar lines up with the measurements of 

panel “B”.

5. Load forms and press start (refer to OPERATION on page 2).

Uneven “C” / Return Mailer

1. Measure the length of panel “A” & “B”.

2. Adjust the upper fold plate so that the bar lines up with the measurements of 

panel “A” & “B”, for example: if panel “A” + “B” is 10 1/2” long move the bar up 

or down so that it lines up with the 10 1/2” mark on the fold plate.

3. Measure the length of panel “B”.

4. Adjust the lower fold plate so that the bar lines up with the measurements of 

panel “B”.

5. Load forms and press start (refer to OPERATION on page 2).

Panel A

Panel B

Panel A

Panel B

5. To reinstall the lower fold plate, slide the plate (with the thumbscrews facing up and throat toward inside of 

machine, figure 5b) until it rests on the two silver bars (figure 5a) and locks into place (figure 5c).

Bars

Figure 5a

Figure 5b

Figure 5c

Summary of Contents for AutoSeal FD 1506













Reviews: