Forlinx SBC OKMX8MPQ-C User Manual Download Page 2

Page: 2 / 59

Attentions

MUST READ BEFORE WORKING WITH OKMX8MM-C

Product Operation Environment:

Hot-plug of CPU module and peripheral modules is strictly prohibited.

Please follow all the warnings and instructions marked on the product.

Please keep the product dry. Once splashed or immersed by any liquid, cut off the power and

dry it out immediately.

Please store and operate the product in ventilating conditions to avoid damages brought by

over high temperature.

Please do not use or store the product in dusty or untidy conditions.

Please do not use or store the product in alternate cold and hot conditions to avoid

condensing which will damage components.

Please do not treat the product rudely. Any falling-off, knocking and violate shaking may cause

destruction to circuit and components.

Please do not clean the product with organic solvents or corrodible liquids.

Please do not dismantle or repair the product by yourself. Contact us when the product

malfunctions.

Please do not modify the product by yourself or use fittings unauthorized by us. Otherwise,

the damage caused by that will be on your part and not included in guarantee terms.

Any questions please feel free to contact Forlinx Technical Service Department..

Summary of Contents for SBC OKMX8MPQ-C




























































Search results

Summary of Contents for SBC OKMX8MPQ-C

Reviews:

Brands by name

Popular brands

Forlinx SBC OKMX8MPQ-C, User Manual

Search results

Summary of Contents for SBC OKMX8MPQ-C

Reviews:

Brands by name

Popular brands