background image

12   

│   

Installing the Forest Shuttle

®

 S / M / L  

Z-Wave

 

 

 
Forest Shuttle is not suitable for humid spaces, like bathrooms or outdoors. 
It is important for the safety of persons to follow these instructions. Save these instructions. 
Do not use the product for any other purpose than intended. In order for the Forest Shuttle S / M / L to function 
correct and safe, the complete curtain system must be assembled with original parts and devices of Forest Group 

Nederland B.V. This includes all components of the curtain track and power supply adaptor. 

 

Forest Group does not assume liability for resulting damages to property or personal injury, defects, labour on location, service 
calls, reinstallation or expenses involved shipping, packing or returning goods, if the product has been abused/modified in any 
way or damaged by improper use or failure to observe these operating instructions. The warranty/guarantee will then expire! 
 
Do not allow children to play with the system or controls. Keep remote controls away from children. 
Frequently examine the installation for imbalance and signs of wear or damage. Do not use if repair or adjustment is necessary. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

v1_3 

Summary of Contents for SHUTTLE L Z-Wave













Reviews: