Forest-Master Fast Fire FM6FF-139 Manual Download Page 22 | Manualshive

Page: 22 / 28

background image

22

FM6FF & FM8FF (Electric & Petrol

Maintenance

PETROL ENGINE

For maintenance and trouble shooting of the petrol engine, see the manufacturer’s handbook
included separately.

STORAGE

This machine should be dried before storing and must be stored in an enclosed dry environment. If
it is left in a damp humid environment then water damage may occur to the motor. It should not be
stored under a wood store.

PROBLEM

PROBABLE CAUSE

REMEDY

Fails to split logs

Log is improperly positioned

Refer to “Operation” section for correct
log loading.

The sizes or hardness of the log exceeds
the capacity of the machine

Reduce the log sizes before splitting it on
the log splitter

Electric motor will not
start

Power cord is not plugged in

Plug in to power source

Fuse or circuit tripped

Replace fuse or reset breaker

Damaged power cord

Contact Technical Support

Motor hums but does not start, faulty
capacitor

Replace capacitor

Ram will not retract or
retracts slowly

Debris in the rack system

Clean / lube rack system periodically

Return spring is damaged or worn

Inspect / replace return spring

Drive belt noise
during start up or
splitting operation

Drive belt is worn

Replace drive belt

«
...
20
21
22
23
24
...
»

Summary of Contents for Fast Fire FM6FF-139





























Reviews:

No comments

Related manuals for Fast Fire FM6FF-139

BC 1826 Big Cheef

Brand: Brave Pages: 12

Brand: Brave Pages: 28

Brand: Craftsman Pages: 27

Brand: Northline Express Pages: 15

Brand: Logmaster Pages: 11

Brand: Hearth & Home Pages: 14

Brand: Hud-son Pages: 44

WALLENSTEIN WE230

Brand: EMB Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands