FORESIGHT SIM-IN-A-BOX BIRDIE PACKAGE Assembly Instructions Manual Download Page 40 | Manualshive

Page: 40 / 49

background image

STEP 4:

COMPONENT SETUP

ASSEMBLY INSTRUCTIONS

EAGLE PLUS / BIRDIE PACKAGE

VERSION 1.1

PAGE 40

Place the computer, Mouse/Keyboard, and Projector on the Rolling Computer Cart as shown.
Then connect the following:

∙

Connect the projector to the Computer using the provided HDMI cable.

∙

Connect the Wireless Mouse/Keyboard to the Computer via BlueTooth.

∙

Connect the Computer to the internet via Ethernet, or connect via WiFi if available.

∙

Connect power cords to Computer and Projector and connect to power supply.

4

WALL

PORT

Keyboard

& Mouse

Projector

Computer

«
...
38
39
40
41
42
...
»

Summary of Contents for SIM-IN-A-BOX BIRDIE PACKAGE


















































Reviews:

No comments

Related manuals for SIM-IN-A-BOX BIRDIE PACKAGE

Brand: Walimex Pro Pages: 4

Brand: PACIFIC CYCLE Pages: 112

Brand: E+E Elektronik Pages: 14

Brand: E+E Elektronik Pages: 26

Brand: E+E Elektronik Pages: 28

Brand: E+E Elektronik Pages: 2

Brand: BW Pages: 8

Electronic Parking Disc II

Brand: Jacob Jensen Pages: 28

Brand: Monacor Pages: 2

Brand: Oki Pages: 8

Brand: Oki Pages: 51

Brand: Tao Motor Pages: 3

Brand: UltraGauge Pages: 55

Brand: Valor Pages: 72

StudSensor HD25

Brand: Zircon Pages: 2

Brand: Oki Pages: 20

Brand: iDataLink Pages: 99

Brand: Dufco Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands