Ford POWER STROKE 2013 Manual Download Page 61

Page: 61 / 95

Air filter replacement:

When replacing the air filter element, use the Motorcraft® air filter
element listed in

Motorcraft part numbers

in the

Capacities and

Specifications

chapter.

Failure to use the correct air filter element may result in severe
engine damage.

1. Locate the mass air flow sensor
electrical connector on the air inlet
tube. This connector will need to be
unplugged.

Unlock the locking clip on the
connector, then squeeze and pull
the connector off of the air inlet
tube.

2. Release the four clamps that
secure the cover to the air filter
housing. Push the air filter cover
forward (away from you) and up
slightly to release it.

3. Remove the air filter element from the air filter housing.

Maintenance

2013 Diesel

(67l)

Supplement, 1st Printing
USA

(fus)

Summary of Contents for POWER STROKE 2013
































































































Search results

Summary of Contents for POWER STROKE 2013

Reviews:

Related manuals for POWER STROKE 2013

Brands by name

Popular brands

Ford POWER STROKE 2013, Manual

Search results

Summary of Contents for POWER STROKE 2013

Reviews:

Related manuals for POWER STROKE 2013

Brands by name

Popular brands