background image

SELECTIVE CATALYTIC REDUCTION (SCR) SYSTEM

Your vehicle is equipped with a selective catalytic reduction (SCR)
system to help reduce emission levels of oxides of nitrogen from the
exhaust of the diesel engine. The system automatically injects diesel
exhaust fluid (DEF) into the exhaust system to enable proper SCR
function.

Importance of maintaining the DEF level

In order for the SCR system to operate properly, the DEF level must be
maintained. Generally, the DEF tank should be filled during the oil
change service interval. See the

scheduled maintenance information

in

this supplement for more information. However, certain conditions or
driving styles, such as trailer towing or fast rates of acceleration, will
require the refilling of the DEF tank more often.

The engine control unit will monitor the amount of fluid available in the
DEF tank. Running a system check in the message center will indicate
whether the DEF level is ok or if it is less than 1/2 full. A message will
automatically be displayed in the message center when the DEF level is
low and needs to be refilled. When you see this message you should refill
your tank. See the

Information displays

chapter of your

Owner’s

Manual

for information display functions. For instructions on refilling

your DEF tank, see

Filling the DEF tank

in the

Fuel and Refueling

chapter.

DEF warning messages and vehicle operations

WARNING:

Diesel Exhaust Fluid (DEF) must be refilled when

low or replaced when contaminated or the vehicle speed will be

speed limited to 50 mph (80 km/h). In these conditions, drive with
caution and refill DEF immediately. If the DEF becomes empty or
contaminated fluid is not replaced, the vehicle will become limited to
idle speed only once stopped. In these conditions, be cautious where
you stop the vehicle because you may not be able to drive long
distances and will not be able to maintain highway speeds until DEF is
refilled or replaced.

WARNING:

Tampering or disabling your vehicle’s exhaust

aftertreatment system will result in severe vehicle performance

limitation including eventual speed limiting to 5 mph.

Fuel and Refueling

19

2013 Diesel

(67l)

Supplement, 1st Printing
USA

(fus)

Summary of Contents for POWER STROKE 2013
































































































Reviews: