manualshive.com logo in svg

Ford POWER STROKE 2013, Manual, Page: 40 / 95

Share
Download
Ford POWER STROKE 2013 Manual Download Page 40

Optional information display procedure

1. Start with the vehicle engine fully warmed.

2. From the main menu, select Gauge Mode and scroll through until one
of the following options appear:

•

If the DPF needs cleaning and the vehicle is warmed up, you will be
prompted to hold OK to clean

Exhaust xx% Full

or

Exhaust Filter

Full

. Press OK and then follow the prompts regarding exhaust

position as needed to initiate OCR. Be sure to understand each
prompt. If you are not sure what is being asked by each prompt,
contact your authorized dealer. The display will confirm the operation
has started and when it has finished.

•

When the exhaust system is
overloaded cleaning will be
allowed until a certain saturation
level. If the vehicle is warmed up and ready the powertrain fault
indicator will illuminate and you will be prompted to hold OK to clean

Drive to Clean Exhaust System

+

Exhaust Filter Overloaded

.

Press OK and then follow the prompts regarding exhaust position as
needed to initiate OCR. Be sure to understand each prompt. If you are
not sure what is being asked by each prompt, contact your authorized
dealer. The display will confirm the operation has started and when it
has finished. You can also drive to clean the filter. See

Active

regeneration

earlier in this chapter.

•

The service engine soon light will
illuminate and the following
messages

Exhaust Filter

Overloaded

+

Reduced Engine Power

or

Reduced Engine Power

will appear when the system is at the point of oversaturation you will
not be able to allow cleaning . The vehicle must be serviced by an
authorized dealer.

3. Once OCR starts, the engine’s rpm will rise to approximately 2,000 -
2,400 rpm and the cooling fan will increase speed; you will hear a change
in audible sound due to the fan and engine speed increase.

It is not necessary to open the hood on the engine compartment. Once
OCR is complete, the engine rpm and fan will return to normal idling.
The exhaust system will remain very hot for several minutes even after
regeneration is complete. Do not reposition the vehicle over materials
that could burn until the exhaust system has had sufficient time to
cool. Depending on the amount of soot collected by the DPF, ambient
temperature, and altitude, OCR may last from 10 to 25 minutes.

Fuel and Refueling

39

2013 Diesel

(67l)

Supplement, 1st Printing
USA

(fus)

Summary of Contents for POWER STROKE 2013
































































































Reviews:

No comments