Ford M-6007-Z427AFT Installation Instructions Manual Download Page 12 | Manualshive

Page: 12 / 19

background image

M-6007-Z427AFT/ART
Crate Engine
INSTALLATION INSTRUCTIONS

NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF

FORD RACING PERFORMANCE PARTS.

Techline 1-800-367-3788

Page 12 of 19

IS-1850-0387

Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356

INTAKE MANIFOLD INSTALLATION INSTRUCTIONS FOR FORD RACING CRATE LONG BLOCKS

! ! ! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION.

AT ANY TIME YOU DO NOT UNDERSTAND THE INSTRUCTIONS, PLEASE CALL THE FORD RACING

TECHLINE AT 1-800-367-3788 ! ! !

Below is a picture of everything needed to accomplish the installation.

•

M-9439-A50 intake gaskets, these are included with your crate engine

NOTE: Cork end rail gaskets are not used

•

(12) Intake manifold bolts 5/16-18 UNC grade 8, with flat washers

•

Torque wrench

•

Motorcraft TA-29 silicone or equivalent RTV high temperature silicone sealer

•

6” Ruler and set of feeler gauges

•

Surface cleaner (Brake Cleaner) or lacquer thinner (not pictured)

•

A gasket sealer/contact cement: such as Gasgacynch®, High Tack® or Indianhead®

«
...
10
11
12
13
14
...
»

Summary of Contents for M-6007-Z427AFT




















Reviews:

No comments

Related manuals for M-6007-Z427AFT

Brand: O.S. engine Pages: 5

MAX-15CV-R Series

Brand: O.S. engine Pages: 19

Brand: Geely Pages: 198

Brand: Marcato Pages: 42

Brand: DoorHan Pages: 16

Brand: Doosan Pages: 179

Brand: YS Pages: 2

Brand: Vauth-Sagel Pages: 14

Brand: Wood-mizer Pages: 13

Brand: ZIEHL-ABEGG Pages: 17

Brand: Honda Pages: 54

Brand: CAB Pages: 16

Brand: Ford Pages: 71

Brand: Yanmar Pages: 406

Brand: Vanguard Pages: 72

VLT Brook Crompton Motor FCM 300

Brand: Danfoss Pages: 102

Brand: Saito Pages: 20

Brand: ebm-papst Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands