16
17
*
if equipped
SecuriCode
™
Keyless Entry Keypad
*
Lock or unlock the doors
without using a key. You can
operate the keypad with the
factory-set, 5-digit entry code.
This code is on the owner’s
wallet card in the glove box.
In addition to the factory-set code, you can
also create up to five of your own 5-digit
personal entry codes.
To lock all of the doors and the liftgate, press
and hold
7•8
and
9•0
at the same time
with the driver’s door closed. For complete
information, refer to the
Locks
chapter in your
Owner’s Manual
.
SelectShift
®
Automatic Transmission
To enable, move the SelectShift gearshift lever
from drive (D) to sport (S). Sport mode selects
the optimum gear for best performance. This
gear selection is typically lower than that of
drive (D) and the shifts are faster.
When the vehicle is in sport mode, it enables
a manual gear selection when you use the
paddle shifters or the button on the side of the
gearshift lever. Press (+) to upshift, press (–)
to downshift. Move the gearshift lever to drive
(D) to return to automatic control.
Blind Spot Information System
(BLIS
®
) and Cross Traffic Alert
*
BLIS aids you in
detecting vehicles
that enter into
your blind spot
zone. Cross traffic
alert warns you of
vehicles approaching from the sides when the
transmission is in reverse (R).
Both systems display an amber indicator
light in your exterior mirrors. Cross traffic alert
also sounds tones and displays messages
to warn you from which direction vehicles
are approaching. For more information
on Cross Traffic Alert, see page 23.
Refer to the
Driving Aids
chapter in your
Owner’s Manual
for more information.
MyKey
®
MyKey allows you to program certain driving
restrictions in order to promote good driving
habits. For complete information, refer to the
MyKey
chapter in your
Owner’s Manual
.
Wiper Operation
Adjust the wiper lever and its controls to
operate the front and rear wipers.
•
Single wipe: Pull the lever down.
•
Intermittent wipe: Raise the lever
upward to position 1 and then rotate
the control:
- upward for short wipe intervals.
- downward for long wipe intervals.
•
Normal wipe: Raise the lever upward
to position 2.
•
High-speed wipe: Raise the lever to
position 3, its highest position.
Washing the Windshield
To operate the windshield washer, pull
the wiper lever toward you.
Speed Dependent Wipers
When your vehicle speed increases, the
interval between wipes decreases.
Autowipers
*
The wipers operate when the system
detects moisture on the windshield, and
adjusts the wiper speed automatically.
Use the rotary control to adjust the
sensitivity of the rain sensor.
•
Low sensitivity: The wipers
automatically operate when the
sensor detects a large amount of
moisture on the windshield.
•
High sensitivity: The wipers
automatically operate when the
sensor detects a small amount of
moisture on the windshield.
Note:
Keep the outside of the windshield
clean. Dirt, bugs and excessive road debris
can prevent it from detecting rain.
To Reduce Smearing, We Recommend
the Following:
•
Lower the sensitivity of the autowipers.
•
Switch to normal or high-speed wipe.
•
Switch the autowipers off.
Note:
Make sure you switch off the
windshield wipers before entering a
car wash.
Rear Window Wiper and Washer
To operate the wiper, press the rocker
switch on the end of the lever to change
between off, intermittent and low speed.
When you switch on the front wipers and
move the gearshift lever to reverse (R),
the rear intermittent wiper automatically
turns on.
To use the rear washer, push the wiper
lever away from you. When you release
the lever, the rear wiper operates for a
short time.
Rear View Camera
This system provides a video
image of the area behind
the vehicle. The image
automatically appears when
the vehicle is in reverse (R)
and uses green, yellow and
red guides to alert you of your
proximity to objects.
Note:
If mud, water or debris
obstructs the camera’s view,
clean the lens with a soft,
lint-free cloth and non-
abrasive cleaner.
*
if equipped
Function
