EN-
US
Ford Connected Charge Station Installation manual
3
SKML9J-10C823-BA
3
Unit description
This document describes the Ford Connected Charge Sta-
tion. You can find the exact device details on the type label
of the Ford Connected Charge Station.
Electrical
characteristics
SAE
Nominal current
(A)
(configurable con-
nected load values)
48A
Line voltage (VAC)
(nominal)
240 V (Line-to-line voltage)
Grid frequency (Hz)
(nominal)
60 Hz
Overvoltage cate-
gory
II
Protection class
I
Residual current de-
vice
See table 4.
Integrated power
meter
Ac/- 5%
Connections
Cable feed
Mounted on-wall, or in-wall
Connection cross-
section
(wire dimension)
2x 6 AWG (L1/L2) 1x 8 AWG (GND)
(follow local codes/regulations)
Charging cable (in-
cluding coupler)
Charging cable with Type 1 coupler ac-
cording to SAE J1772
Cable length 20 ft / approximately 6
m
Output voltage (V
AC)
240 V
Maximal charging
capacity (kW)
11 kW
Communication &
features
Electrical
characteristics
SAE
Vehicle–charger
Communication
Protocol (CP)
SAE J1772
Authentication
Bluetooth (BLE 4.2) – Setup App
Display
9 RGB-LEDs
Network interfaces Wi-Fi 802.11n - 150 Mbit/s
Authentication and
mobile communica-
tions
Bluetooth (BLE 4.2) - Setup-App
OCPP
Version 1.6
Mechanical data
Dimensions (W × H
× D)
10.2 x 17.7 x 5.5 Inches
258 x 450 x 141 mm
Weight (including
wall mount bracket
& charging cable)
17.53 lbs
7.95 kg
Installation height Minimally 35 inches above floor level
(regarding to the bottom of the de-
vice)
Minimally 900 mm above floor level
(regarding to the bottom of the de-
vice)
IP protection class
NEMA Type 3S, IP65
Protection against
mechanical impact
UL2994
Ambient conditions
Operating tempera-
ture range
-40°F to +140°F
-40°C to +60°C
Storage tempera-
ture range (°C)
-40°F to +185°F
-40°C to +85°C
Altitude (m)
Max. 9,842 ft above sea level
Max. 3,000 m above sea level
Certification com-
patibility
Electrical
characteristics
SAE
Other standards
and guidelines
ANSI/UL2594:2016 / CAN/CSA C22.2
No. 280-16
ANSI/UL2231-1:2012 / CAN/CSA C22.2
No. 281.1-12
ANSI/UL2231-2:2012 / CAN/CSA
C22.2 No. 281.2-12
FCC Part 15, Subpart B / ICES003
FCC Part 15, Subpart C / RSS.2010 /
RSS-GEN
NEC Article 625 compliant
Tested OCPP back-
ends
Ford OCPP (Open Charge Point Proto-
col) server
NOTICE
A shutdown, or a reduction in charging current, may oc-
cur to prevent the charge station overheating.
3.1
In the box
Scope of delivery for the Ford Connected Charge Station.
See Fig. 19 on the inside of the back cover.
A
Main unit
B
Design cover
C
Charging cable with coupler
D
Blind plugs
E
Wall mount bracket
F
Dock rear holder, dock front cover & dock insert
G
Screw M5 x 12 mm
H
Screw M4 x 16 mm
See also chapter 5.3.1, "Required tools" on page 5.
3.2
Wireless interface connections
3.2.1
Bluetooth
The Bluetooth connection is used to set up the Wi-Fi AP
(access point) when starting up the charge station. Note
that you cannot control the charging charge station
through Bluetooth.
