manualshive.com logo in svg

Ford 2010 05+ Mustang, Owner'S Manual

Share
Download
Ford 2010 05+ Mustang Owner'S Manual Download Page 91

KEYS

Your vehicle is equipped with two
Integrated Keyhead Transmitters
(IKTs). The IKT functions as both a
programmed ignition key that
operates all the locks and starts the
vehicle, and a remote keyless entry
transmitter.

Your IKTs are programmed to your vehicle; using a non-programmed key
will not permit your vehicle to start. If you lose your authorized dealer
supplied IKTs, replacement IKTs are available through your authorized
dealer. Standard SecuriLock™ keys without remote entry transmitter
functionality can also be purchased from your authorized dealer if
desired.

Always carry a spare key with you in case of an emergency.

For more information regarding programming replacement IKTs, refer to
the

SecuriLock™ passive anti-theft system

section later in this chapter.

Note:

Your vehicle’s IKTs were

issued with a security tag that
provides important vehicle key cut
information. It is recommended that
you keep the tag in a safe place for
future reference.

2010 05+ Mustang

(197)

Owners Guide, 1st Printing
USA

(fus)

Locks and Security

91

Summary of Contents for 2010 05+ Mustang































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands