Ford 2010 05+ Mustang Owner'S Manual Download Page 205

Page: 205 / 318

When features of the AdvanceTrac

威

system are off, the “sliding car off”
icon

will illuminate steadily.

Pressing the AdvanceTrac

威 ⬙

Off

⬙

control switch again will turn off the
“sliding car off” icon.

In R (Reverse), ABS and the Engine and Brake Traction Control features
will continue to function; however, ESC is disabled.

AdvanceTrac

威

Features

Control
switch
functions

Mode

“Sliding

car off”

icon

Message

Center Dis-

play (if

equipped)

ESC

Trac-

tion

Con-

trol

Default at
start-up

turns on

during

bulb

check

En-

abled

En-

abled

Control
switch
pressed
once mo-
mentarily

Traction

Control OFF

TRACTION

CONTROL

OFF

En-

abled

Dis-

abled

Control
switch
pressed
twice rap-
idly, brakes
applied and
no throttle
apply

Sport Mode

(if

equipped)

ADVANCE

TRAC

SPORT

MODE

En-

abled

En-

abled

2010 05+ Mustang

(197)

Owners Guide, 1st Printing
USA

(fus)

Driving

205

Summary of Contents for 2010 05+ Mustang































































































































































































































































































































Search results

Summary of Contents for 2010 05+ Mustang

Reviews:

Brands by name

Popular brands

Ford 2010 05+ Mustang, Owner'S Manual

Search results

Summary of Contents for 2010 05+ Mustang

Reviews:

Brands by name

Popular brands