manualshive.com logo in svg

Ford 2006 Expedition, Owner'S Manual

Share
Download
Ford 2006 Expedition Owner'S Manual Download Page 96

5. Locate the vertical adjuster on
each headlamp, then use a 10 mm
socket/wrench to turn the adjuster
either counterclockwise (to adjust
down) or clockwise (to adjust up)
aligning the upper edge of the light
pattern up to the horizontal line.

6. HORIZONTAL AIM IS NOT
REQUIRED FOR THIS VEHICLE
AND IS NON-ADJUSTABLE.

7. Repeat Steps 3–5 for the other headlamp.

8. Close the hood and turn off the lamps.

TURN SIGNAL CONTROL

•

Push down to activate the left
turn signal.

•

Push up to activate the right turn
signal.

INTERIOR LAMPS

Front row map lamps (if equipped)

To turn on the map lamps, press the
rear edge of the lamp.

I N T 2

O F F

OFF

I N T 1

2006 Expedition

(exd)

Owners Guide (post-2002-fmt)
USA

(fus)

Lights

96

Summary of Contents for 2006 Expedition

















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands