manualshive.com logo in svg

Ford 2006 Expedition, Owner'S Manual

Share
Download
Ford 2006 Expedition Owner'S Manual Download Page 285

Fuse/Relay

Location

Fuse Amp

Rating

Passenger Compartment Fuse

Panel Description

R203

PCM relay

Fuse 32, Fuse 34, PCM solenoids
and sensors

R301

Trailer tow

back-up lamp

relay

Trailer tow 7–wire connector
(back-up lamps)

R302

Heated PCV

valve relay

Heated PCV valve

R303

Fuel pump relay Fuel pump shut-off switch, PCM

(fuel pump monitor), Fuel pump,
Fuel pump driver module

R304

Battery saver

relay

Roof rail lamps, Vanity mirror
lamps, Map/Dome lamp, Glove box
lamp, Cargo area lamp, Outside
mirror puddle lamps, Instrument
cluster (interior lamps)

R305

Horn relay

Dual note horn

* Mini Fuses ** Maxi Fuses

Note:

Relays R301–R305 are not serviceable components; see your

authorized dealer for assistance.

CHANGING THE TIRES

If you get a flat tire while driving, do not apply the brake heavily.
Instead, gradually decrease your speed. Hold the steering wheel firmly
and slowly move to a safe place on the side of the road.

Your vehicle may be equipped with a conventional spare tire that is
different in one or more of the following: type, brand, size, speed rating
and tread design. If this is the case, this dissimilar spare tire is still rated
for your vehicle loads (GAWR and GVWR). Your vehicle may be equipped
with a spare wheel that may not match the road wheels and is not
equipped with a Tire Pressure Monitor System (TPMS) sensor.

The use of tire sealants may damage your tires. The use of tire
sealants may also damage your Tire Pressure Monitoring System.

2006 Expedition

(exd)

Owners Guide (post-2002-fmt)
USA

(fus)

Roadside Emergencies

285

Summary of Contents for 2006 Expedition

















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands