manualshive.com logo in svg

Ford 2006 Expedition, Owner'S Manual

Share
Download
Ford 2006 Expedition Owner'S Manual Download Page 174

Shorten and fasten the belt when
not in use.

All of the passenger combination lap and shoulder belts have two types
of locking modes described below:

Vehicle sensitive mode

This is the normal retractor mode, which allows free shoulder belt length
adjustment to your movements and locking in response to vehicle
movement. For example, if the driver brakes suddenly or turns a corner
sharply, or the vehicle receives an impact of approximately 5 mph (8 km/h)
or more, the combination safety belts will lock to help reduce forward
movement of the driver and passengers.

Automatic locking mode

In this mode, the shoulder belt is pre-locked. The belt will still retract to
remove any slack in the shoulder belt.

The automatic locking mode is not available on the driver safety belt.

When to use the automatic locking mode

•

Anytime

a child safety seat (except a booster) is installed in the

vehicle. Children 12 years old and under should be properly restrained
in the rear seat whenever possible. Refer to

Safety restraints for

children

or

Safety seats for children

later in this chapter.

2006 Expedition

(exd)

Owners Guide (post-2002-fmt)
USA

(fus)

Seating and Safety Restraints

174

Summary of Contents for 2006 Expedition

















































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands