background image

FORCE1 RC

4

7.4V 1800mAh Li-Po Batteries

LI-PO BATTERY CARE

Avoid Overheating

Your batteries will sometimes be warm/hot to the touch after use. This is normal, but beware that battery 
components will fail if not allowed to cool down between uses. Also, do not leave batteries exposed to 
direct sunlight. 

Store Properly

Store batteries at room temperature, between 5C°/40°F and 27°C/80°F.

Use Carefully

 • Leave time between charging and using the battery

 • To extend the lifetime of the battery, always keep about 20% of the power remaining in the drone 

battery (rather than completely draining it) 

 • If the battery is pushed beyond its limits, the battery could get hot and the performance will drop

 • When using the battery for a long time, the battery will increase in temperature. If it is sealed, the air 

inside will inflate rapidly causing further heating 

Charging

• DO NOT overcharge the battery; never charge batteries unattended, and stop charging as soon as your 

batteries indicate they are charged  

• DO NOT attempt to charge batteries that appear damaged in any way (cracking, swelling, discoloration, etc.) 

• If you feel a battery isn’t charging properly, try using another charger if possible. If you find your battery 

or charger is defective, please visit force1rc.com for a replacement, or email us at [email protected]

• To inspect a battery, remove it from the device and examine the battery, battery pins and contacts. If 

you notice damage, please visit force1rc.com for a replacement, or email us at [email protected] 

• Check your battery and connections after every crash

• Please use genuine factory parts and replacements from force1rc.com 

Summary of Contents for F100 GHOST























Reviews: