background image

 
 

 

ASSEMBLY MANUAL - FORCE USA LEG CURL / LEG 
EXTENSION ATTACHMENT  F-LEGA 

BEFORE YOU START 

The F-LEGA is an attachment for the F-FID Flat Incline Decline Bench which must be purchased and 
assembled separately. 

Remove all parts from the packaging, separate and count each various component, to ensure everything has been 
correctly provided. 

Follow the instructions and consult both the individual assembly pages and the overall expanded views of the 
equipment. 

Certain parts may arrive pre-assembled from the factory. 

It is the owner’s responsibility to ensure that all users of this unit have read the owner’s manual and are familiar 
with the safety precautions. 

 

SAFETY PRECAUTIONS 

 

Highly recommended for two or more people to assemble the equipment to avoid injury.

 

 

Assemble the equipment on a flat level surface. 

 

Consider placing a mat under the equipment to protect your floor. 

 

Wear appropriate footwear and clothing during assembly and use. 

 

Only tighten nuts and bolts by hand until the whole equipment is assembled. 

 

Ensure you correctly orientate each piece before attaching. 

 

Do not allow children and pets to be unsupervised around the assembly or usage of this equipment. 

 

Ensure all parts are in full working order before use. 

 

Only one person should use the machine at any one time. 

 

Do not use the equipment outdoors or around water. 

 

Keep hair, fingers or clothing away from moving parts. 

 

Only use attachments recommended by the manufacturer. 

 

Never operate if any parts are not functioning correctly. 

 

Always correctly stretch and warm up before using the equipment. 

 

Stop immediately

 if your experience any pain, dizziness or nausea. See a doctor at once. 

PLEASE NOTE:

  Descriptions of pieces as LEFT and RIGHT are from the point of view of standing 

behind the 

equipment facing towards the front. 

Any instructions relating to parts of the F-FID have been shown in 

Italics

 to help avoid confusion. 

BEFORE STARTING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR. ESPECIALLY IF YOU ARE OVER 
THE AGE OF 35 OR HAVE PRE-EXISTING HEALTH PROBLEMS.  
READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING ANY FITNESS EQUIPMENT.  
FORCE USA FITNESS EQUIPMENT ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY 
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. 
 

SAVE THESE INSTRUCTIONS 

 

Summary of Contents for F-LeGA









Reviews: