background image

www.fonicainternational.com

www.fonicainternational.com

FLAG 

ISODYNAMIC SPEAKERS

5

4

FLAG 

ISODYNAMIC SPEAKERS

1 / WARNINGS

• For any assistance intervention, please contact qualified personnel.
• To safely proceed with the assembly and installation of the M and L model, we recommend 
the assistance of a second person.
• Do not expose the speakers to dripping or splashing and do not place objects containing 
liquids above it.
• Do not place the speakers near heat sources, in humid or too cold environments.
• Temperature of use: from 10 to 35°C.
• Do not expose the device to direct sunlight.
• Keep the device away from sharp objects and objects that may be attracted to magnets.

[ACTIVE VERSIONS ONLY]
CAUTION RISK OF ELECTRIC SHOCK!

Do not open the device for any reason, even if disconnected 
from the mains.

CAUTION!

It is important to avoid touching the speaker’s part covered 
with fabric. Below it there is the speaker’s membrane which 
may be damaged by contacting with foreign objects. Please 
keep in mind, when you need to move the speaker, to always 
hold the profile’s perimeter, without touching the fabric. 
Always handle and move the speaker holding the perimeter 
profile without touching the fabric. Always use the perimeter 
profiles without taking them off. They must not be pulled as 
they could come off.

CAUTION!

Under the entire surface of the fabric there are powerful ma-
gnets and a delicate membrane therefore this surface must 
never impact with any type of stuff or being put beside ma-
gnets or ferromagnetic objects that could be attracted to the 
speaker’s surface.

CAUTION!

The speaker, if correctly installed on its base, is in firm ba-
lance. Slight fluctuations of the panel are usual. Do not lean, 
push or modify its balance in any way, as it may cause the 
falling or the overturning of the device.
FONICA INTERNATIONAL S.R.O. does not assume responsi-
bility for any damage caused to people and/or things due to 
assembly and/or an incorrect use of the speaker.

CAUTION!

This speaker is intended for exclusive use together with its 
supplied stand and installed according to the instructions.
The use of the speaker with other supports can lead to pro-
duct instability and cause injury.

CAUTION!

Loudspeakers in the active, powered version require a stable 
ground connection. Verification of the earth connection in the 
power socket where the equipment is  connected by  a quali-
fied person is required. The active loudspeaker must be con-
nected to the protective earth conductor of the system throu-
gh the power cable connected to an earthed power socket. 
This socket must be easily accessible after the installation of 
the loudspeakers. The part of the cables inside the equipment 
that connect the power connector to the switch remains ener-
gized even after the switch is opened.
Never open or disassemble parts of the loudspeakers: they 
contain dangerous parts and can irremediably compromise 
the safety and functioning of the loudspeakers.

Summary of Contents for FLAG




















Reviews: