background image

8

1.6 

Fault / malfunction codes

If a fault/malfunction is detected during boiler operation, the 

message 

"ALL"

 will appear on the display followed by the fault 

code.

If you see alarm 

“02”

 (low water pressure in the system):

–  on the display (1), check that the heating system pressure 

when cold is 

1-1.2 bar

. If this is not the case, open the filling 

valve (2) and restore the heating system pressure until the 

display (1) shows a reading of 

1-1.2 bar

–  close the filling valve (2)

2

1

Fig. 4

If you see alarm 

“06”

 (no flame detected) and 

“07”

 (safety ther-

mostat intervention):

–  press and hold the button 

y

 for more than 3 seconds and 

check whether normal operating conditions are restored.

If this operation is not successful, 

ONLY ONE MORE ATTEMPT

 can 

be made, therefore:

–  close the gas isolation valve

–  set the main system switch to "OFF"

–  contact the Qualified Technical Personnel.

OFF

Fig. 5

CAUTION

Should you see an alarm not described here, contact a 

qualified technical professional

.

2  SHUTDOWN

2.1 

Temporary shutdown

If the user wishes to interrupt boiler operation, press and hold 

the button 

y

 for at least one second, once if in "WINTER 

mode" 

n

 or twice if in "SUMMER mode" 

l

.

"- -"

 will appear on the display.

ELECTRICAL HAZARD

The boiler will still be powered.

If the user is away temporarily, for a weekend, short trip etc and 

if the outside temperature is at ZERO:

–  press and hold the button 

y

 once if in "WINTER mode" 

n

 

or twice if in "SUMMER mode" 

l

 to put the boiler into stand-

by

–  set the main system switch to "OFF"

–  close the gas valve.

OFF

Fig. 6

CAUTION

If the outside temperature might fall below ZERO, 

since the appliance is equipped with an "antifreeze 

function"
–  ONLY PUT THE BOILER INTO STAND-BY
–  leave the main system switch set to "ON" (boiler is 

powered)

–  leave the gas valve open.

Summary of Contents for UNIQA.REVOLUTION





















































Reviews: