background image

 CAUTION!

 

§

Wear rubber gloves and safety goggles (or face shield) when handling SafeCLEAN Plus solution.

 

§

Use only Follett approved cleaners.

 

§

Do not use solvents, abrasive cleaners, metal scrapers or sharp objects to clean any part of the dispenser.

SafeCLEAN Plus Solution:  Follow the directions on the SafeCLEAN Plus packaging to mix 1 gal. (3.8 L) of Follett 

SafeCLEAN Plus solution. Use 100 F (38 C) water.

Cleaning Procedure

Note: Check drains and drain cup to ensure they are open and flowing freely. 

1. 

If ice machine was running recently, ensure that the evaporator is completely free of ice before proceeding. 

If there is ice in the evaporator, complete steps 2-7 using only hot water to remove the ice, then begin 

Cleaning Procedure again.

2.  Remove front or top cover. 
3.  Disconnect bin signal cable from ice machine electrical box.
4.  Press CLEAN switch. The MAINTENANCE light will turn on and the machine will drain. Wait for the LOW 

WATER light to turn on.

5.  Remove lid from cleaning cup and fill (about 1 quart) until SafeCLEAN Plus solution completely fills the 

reservoir. Place lid back on cup.

6.  CLEANER FULL light will turn on and machine will start cleaning cycle then rinse three times; this process 

takes approximately 15 minutes.

7.  When machine is finished cleaning, the MAINTENANCE light will turn off.
8.  Remove top bearing insulation. Loosen Phillips-head screw on nozzle connected to evaporator. Remove 

nozzle from evaporator side only, leave other side of nozzle connected to transport tube.

9.  Soak one SaniSponge in remaining SafeCLEAN Plus solution.
10. Insert the sponge soaked in SafeCLEAN Plus solution into nozzle then insert a dry sponge into the nozzle.
11. Replace nozzle onto evaporator and tighten screw. Ensure drain is connected to reservoir and vent tubes 

are connected to evaporator drain pan. Replace top bearing insulation.

12. Reconnect bin signal cable. Wait for ice to push sponges through transport tube.
13. Collect sponges from ice storage bin.
14. Replace front or top cover.
15. After 10 minutes, dispense all ice and discard.
16. Clean the dispenser/bin.

Exterior Cabinet

Clean stainless steel panels with stainless steel cleaner.

  

MC_425A/W, MM_425A/W, MF_425A/W, _P425A/W Ice Machines 7

Summary of Contents for Maestro Plus CP425A













Reviews: