background image

7CI100A/7FS100A, 15CI100A/15FS100A

Installation 

 

CAUTION!

No service or maintenance should be performed until the technician 
has thoroughly read this service manual. Except for routine cleaning 
and sanitizing, only qualified technicians should attempt to service 
or maintain this equipment.

Countertop Installation

The 7 Series countertop model is designed to fit on counters underneath 
standard mounted cabinets, this does not apply to 15 Series models. See 

page 4

 for dimensions. Installation instructions for freestanding model 

may be found on 

page 9

.

1.  A clearance of at least 3" (7.62 cm) is required behind and on 

each side of the dispenser for electrical connection and ventilation 
(Fig. 1).

2.  Rough-in the electrical service and water line. 

 

§

Electrical: 115 V, single phase, 15A receptacle required. The dispenser 
has an integral 8 ft (2.4 m) cord and plug.

 

§

Water: supply line (with shut-off valve) connects to the dispenser's  
1/4" MPT or John Guest push-in fitting inlet.

NOTICE!

If installing optional Drip Tray Drain Kit or Leg Accessory, 
complete those steps before proceeding. Refer to instructions 
included with the Drip Tray Drain Kit, or see 

page 9

 for Leg 

Accessory instructions.

Fig. 1 

3.  Connect water line. Recommended routing (Fig. 2) allows easy access 

to water for cleaning and sanitizing procedure.

4.  If installing the optional internal water filter*, please see 

Maintenance/Cleaning Mode on page 12

 before proceeding. If 

not, proceed to step 5.

*  If your dispenser has the internal water filter option, the water filter 

must

 be 

installed for the dispenser to operate. Because internal components will need to 

be accessed for both procedures, Follett recommends installing the water filter 
just prior to initial sanitizing.

5.  Connect power supply.

6.  Sanitize the dispenser prior to use (see the Initial Sanitizing Kit 

instructions shipped with this unit).

Fig. 2 

countertop models

minimum 3" (7.62 cm) 

clearance required

Water Inlet

3' (91.4 cm)

Plug

Valve

Summary of Contents for 7CI100A

















































Reviews: