IMPORTANT NOTES:
DO NOT use this appliance immediately below a fixed socket outlet.
DO NOT use this appliance in the immediate vicinity of a bath, shower, swimming pool or other area where water/moisture could present
a hazard.
• CAUTION: This appliance must not be used in conjunction with any timer, programmer or thermal control, or any other device that will
switch on the appliance automatically, as a fire risk may occur if the heater is accidentally covered or displaced.
• Do not allow the heater to be covered as this may cause overheating. The appliance must not be placed near curtains or similar materi-
al. A clearance space of at least one metre should be allowed in front of the appliance.
• The electrical socket that the appliance uses MUST be easily accessible. Do not route the supply cord directly in front of the heater unit.
• If the cord is damaged, it must be replaced by a service agent or competent person.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsi-
ble for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
INSTALLATION REQUIREMENTS:
The appliance is supplied with a pre-wired three pin plug, (13Amp fuse rated), and 2 metres of electrical cable. It is therefore necessary for
a suitable electrical socket to be located within this distance and be easily accessible.
This appliance is designed to be wall-hung, using the wall fixtures/fixings provided. DO NOT recess any part of appliance into the wall.
UNPACKING THE APPLIANCE:
Read
all the instructions before continuing to unpack or install this appliance. Carefully remove the appliance from its packaging and lay
on the floor with it`s back surface downward. Note: DO NOT stand the appliance on its frame as this may cause distortion. Check that the
remaining packaging contents correlate with the component checklist below. Please dispose of all packaging with care at your local recy-
cling centre.
COMPONENT CHECKLIST:
QUANTITY
DESCRIPTION
1
Wall Heater
1
Bag of Decorative Pebbles
1
Instruction Booklet
1
Screw and Wall-Plug Pack (3 x 40mm pozi pan head screws/3 x wall plugs)
SITE REQUIREMENTS:
The appliance is designed for wall mounting only, at a minimum distance of 100mm from the floor or hearth to the bottom edge of the rear
frame. The wall should be relatively flat and not interfere with any of the various vent holes in the back panel. The wall must be structurally
sound and constructed of a material capable of withstanding moderate heat. Finished plaster, conventional wallpaper, dry-lined plasterboard
are examples of suitable materials. Materials such as “flock blown vinyl” embossed paper which are sensitive to even small amounts of heat
should be avoided as some discolouration may occur.
If the appliance is to be mounted on a dry lined or a timber framed construction wall then the integrity and ability of the wall to carry the
weight of the appliance must be confirmed. It is important in these circumstances that any vapour control barrier and/or structural mem-
ber of the house frame are not damaged.
1
Section
1.0
2.0
3.0
4.0
5.0
6.0
Contents
Important Notes
Installation Requirements
Appliance Data
Unpacking the Appliance
Component Checklist
Site Requirements
Page No.
1
1
1
1
1
1
Section
7.0
8.0
9.0
10.0
11.0
12.0
13.0
Contents
Appliance Disassembly
Fixing the Appliance
Operating the Fire
Safety Cut-Out System
Maintenance
Cleaning
Spares
Page No.
2
2
3
3
3
3
3
1.0
2.0
4.0
3.0
5.0
6.0
APPLIANCE DATA:
Supply Voltage:
230/240V AC, 50Hz
Fuse Rating:
13 Amp
Heating Elements:
2 x 900W/2 x1000W
Lighting:
2 x 60W Fireglow “BC” bulbs
‘Kavachi’
‘Andalusia’
